Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
Thank you for purchasing the RadioShack Jumbo-Digit Atomic Wall Clock with Wireless In/Out Thermometer. Your clock is a multifunctional radio frequency (RF) controlled clock designed to automatically synchronize the current time and date when brought within range of the radio signal from the U.S. Atomic clock. After you install the batteries, the clock automatically searches for a radio signal. $#66'4;"+056#..#6+10 You need two AA alkaline batteries for the clock and two AA alkaline batteries for the thermo-sensor (not supplied ). When o appears, replace the batteries. For the best performance and longest life we recommend RadioShack alkaline batteries. ....#±±±±y+0"6*'"6*'4/1/5'0514 1. Remove the holder from the back of the thermo-sensor. 2. Use a Phillips screwdriver to remove the screws on the battery compartment cover, then slide off the cover. 3. Place the batteries in the compartment as indicated by the polarity symbols (+ and –) marked inside. 4. Replace the battery cover and secure it with the screws. +0"6*'"%.1%- 1. Pull the tab on the battery compartment cover at the back of the clock to remove the cover. 2. Place the batteries in the compartment as indicated by the polarity symbols (+ and –) mark inside. 3. Replace the cover. /1706+0) Place the clock and thermo-sensor on a flat surface using the stand, or mount it on a wall using screws (not supplied). ....#6*'"%.1%-1P"C"(NCV"5WTHCEG Pull the built-in stand away from the back of the clock and set it on a table or other flat surface. 1P"C"9CNN 1. Use a 1/8 inch screw (not supplied) with a head that fits into the keyhole slot on the back of the clock to drill a hole in the wall at the desired mounting location. 2. Thread the screw into the wall until the head extends about . inch from the wall. 3. Position the keyhole slot over the screw and slide the thermometer down to secure it. 6*'"6*'4/1/5'05141P"C"(NCV"5WTHCEG Insert the ends of the supplied wire stand into the holes on the back of the thermo-sensor and set it on a table or other flat surface. 1P"C"9CNN 1. Use two 1/8-inch screws (not supplied) with heads that fit into the keyhole slots on the back of the supplied mounting bracket to drill two holes about 13/4 inches apart on the mounting surface. 2. Thread a screw into each hole so the heads extend about . inch from the mounting surface. 3. Align the keyhole slots on the mounting bracket with the screws and slide the bracket downward to secure it. 4. Slide the remote sensor onto the mounting bracket. Extra-Large LCD — Easy to read from the across the room. Four Time Zones — View Pacific, Mountain, Central, and Eastern time zones. oyappears here if the sensor batteries are weak. 100 Feet (30 meters) Range Remote thermo-sensor temperature and channel Current day of the weekAlarm TimeAlarm Indicator Indoor Temperature Signal Indicator CHANNEL — Press to see the temperature read by each thermo-sensor. Monitor outdoor and indoor temperature with the supplied thermo-sensor. You can use up to three thermo-sensors to monitor the temperature of three different locations. Thermo-sensor Channel Thermo-sensor Temperature ZONE — Press ZONE until the desired time zone appears. Hold down ZONE for three seconds until oy disappears to turn off automatic time setting if you move to an area where a signal is unavailable. ‘AA’ UM3 1.5V ‘AA’ UM3 1.5V HHHH — Press while setting the time or alarm time to advance to the next digit to set. Hold down HHHHyfor a few seconds until oyappears to turn on automatic time setting mode. THERMO — Hold down THERMO and CHANNEL at the same time for about two seconds to search for the signal from the thermosensor. ALARM — Hold down to enter alarm setting mode. When in alarm setting mode, press to set the alarm time hour and minutes. RESET — If the clock stops operating or locks up, you can reset it. Press RESET with a pointed object. The clock starts scanning for a radio signal. Battery Compartment Built-In Stand CLOCK — Press to toggle the alarm time display between seconds and day of the week. Hold down to enter manual time setting mode. When in time setting mode, press CLOCK to set the hour, minutes, year, month, date, and language. The year can be set from 2000 – 2099. Manual setting is overidden by the automatic setting (radio signal) from the atomic clock. Low Battery Indicator — oy appears if the batteries are weak. oyappears here if the clock batteries are weak. xxxx — Shows the temperature trend in the last half hour. LED Display — Blinks when the thermosensor is in normal working condition. ."%#76+10".# Battery Installation • Use only fresh batteries of the required size and type. • Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities. Mounting • Do not place your clock or thermo-sensor in direct sunlight, near electronic appliances, or in a location where it is likely to get wet. 2. °°°° C/°°°° F — Set to °°°° C for Celsiu...