Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
See FIGURE 5 below. FIGURE 5 Too Fine (Loosen) Too Coarse (Tighten) Correct For technical questions, please call 1-800-444-3353; SKU 30224 Page 9 Troubleshooting section at end of manual. Techniques Note: Before spraying, mask all objects you do not want sprayed and lay cloths (not included) on the floors. 1. Always keep the gun at right angles to the workpiece (See FIGURE 6). Pull the Trigger (38) slowly and move the Spray Gun in parallel strokes to the object being painted. Keep the distance from the object being painted at 6” to 9”. This may slightly differ depending on the flow adjustment and the material being sprayed. Do not stop the gun movement while spraying. If you stop the gun for even just a slight pause while spraying, the paint will build up and run down the workpiece. FIGURE 6 (Heavier coat on one side, uneven coverage) Incorrect (Even coverage) Correct (90o) 2. To ensure you don’t allow paint to build up, start moving the Spray Gun before you Squeeze the Trigger (38). When you are finished spraying, release the Trigger (38) before you stop moving the Spray Gun. Doing so will eliminate distinct overlaps, producing a blended (feathered) affect. See FIGURE 7 below. EndBegin ReleaseSqueeze Stroke Trigger (38) FIGURE 7 Trigger (38) Stroke (Top View) Note: The speed of the stroke, the adjustment of the Fluid Control Knob (29), and the distance from the workpiece, will determine how much paint is being applied. To get the best results, try to apply two thin coats of paint versus one thick coat. 3. Clean out the gun thoroughly after EVERY use, according to the instructions found on the next page. For technical questions, please call 1-800-444-3353; SKU 30224 Page 10 Troubleshooting section at end of manual. IMPORTANT: The Spray Gun must be cleaned IMMEDIATELY after use. Improper cleaning is a common reason for the Spray Gun not to work properly. Materials dry quickly which will render the gun useless. It is extremely difficult to remove dry paint from small passages within the Gun. Maintenance SOLVENT SELECTION Always follow the paint manufacturer’s recommendations for cleaning, solvent type, and disposing of used solvent. Latex Paints: Use warm, soapy water. IMPORTANT: Do not use mineral spirits on latex paints or the mixture will congeal making it very difficult to remove. Oil Based Paints: Use mineral spirits. IF A FLAMMABLE SOLVENT NEEDS TO BE USED, ADHERE TO THE FOLLOWING: 1. Follow all of the solvent manufacturer’s clean up instructions and safety precautions at all times. 2. Always flush the Spray Gun a full hose length from the air compressor. 3. If collecting flushed solvents into a metal container, transfer into a larger nonmetal container, and flush the metal container. 4. Work far away from any ignition sources in a vapor free area. After each use: 1. Empty the Paint Cup (47) and clean it with the solvent. 2. Fill the Paint Cup (47) with solvent and spray it through the Gun into a container, while shaking the gun. Once the Paint Cup (47) is empty, repeat the process until the solvent comes out clean. Disconnect from the air source. After disconnecting, be aware that air pressure may still remain in the Spray Gun. Point the Gun into the spent solvent container and squeeze the Trigger again to make sure no air remains. 3. Remove the Air Cap and soak it in solvent until it is clean. Use an old toothbrush and toothpicks to remove any material. Do not use metal objects to clean the Air Cap or you may damage the drilled passages. Inspect the fluid needle and make sure it is not bent. If it is bent, have it replaced by a certified service technician. Warning!! Do not immerse the Spray Gun Body in solvent! 4. Use the appropriate solvent (depending on the material sprayed) to wipe down the Gun body. 5. Always lubricate the Spray Gun after cleaning. You may use a non-silicon oil or a light lubricant on all threaded connections prior to storing the unit. 6. Disposal: After cleaning your Spray Gun, properly dispose of your cleaning solutions according to the solution manufacturer’s direction and local hazardous waste standards. For technical questions, please call 1-800-444-3353; SKU 30224 Page 11 Troubleshooting section at end of manual. Parts List Part Description QTY Part Description QTY Part Description QTY 1S Air Cap Set #1-3 17S Assembly #17-20 32 Body 1 1 Air Cap 1 17 Wiper 1 33 Valve 1 2 Lock Ring 1 18 Retainer 1 34 Gasket 1 3 Zinc Ring 1 19 Sleeve 1 35 Spring 1 4 Fluid Nozzle 1 20 Wiper 1 36 Screw 1 5 Head 1 21 Gasket 1 37 Stud 1 6 Screw 1 22 Housing 1 38 Trigger 1 7 Body 1 39 Screw 1 23 Needle 1 40 Air Inlet 1 8 Stem 1 24 Locknut 1 9 Stem 1 25 Locknut 1 41 Siphon Tube 1 10 Washer 1 42 Vent Tube 1 11 Spindle 1 26 Body 1 43 Arm 1 12 O Ring 1 27 Washer 1 44 Cup Locking Lever 1 13 Pattern Control Knob 1 28 Spring 1 45 Canister Lid 1 14 Cowhide Washer 1 29 Fluid Control Knob 1 46 Lid Gasket 1 47 Cup 1 15 Fluid Needle Packing 1 30 Nut 1 48 Vent Cap 2 16 Packing Nut 1 31 Packing 1 PLEASE READ THE...
Эта инструкция также подходит к моделям:Распылители краски - 30224 (711.85 kb)