Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
risk of Fire or explosion from Materials incompatible with aluminum. Certain solvents, including 1,1,1-Trichloroethane and Methylene Chloride can chemically react with the Aluminum used in this spray equipment. This can cause an explosion which may result in death or serious personal or property injury. Other chemicals ,when mixed, may cause unpredictable results. Inform yourself by reading the information provided with each solvent before introducing to the sprayer. Never spray the solvents named at left in this sprayer which contains Aluminum. Never use these materials for cleaning equipment. Never use any solvent if in doubt of its composition or compatibility with Aluminum, other materials or this spraying equipment. inhalation hazard. Inhaling solvents or sprayed materials may cause severe injury to the lungs or body, due to their chemical make up or the fact that they may coat the interior of the lungs. Use an ANSI approved ventilator or face mask. NOTE: Some face masks, such as paper filters provide only limited protection against harmful sprays and fumes. Consult safety documents provided with the materials you are spraying or an industrial safety expert when determining the appropriate respiratory protection. risk of ejected Objects or Sonic injury. Many components of this tool and any air pressure powered tool are under significant air pressure, even after the air supply is disconnected. A significant risk of injury caused by ejected components or materials diverted by the stream of air pressure exists. High pressure air escaping suddenly may cause hearing injury. Before doing any service to the sprayer, disconnect it from the air supply. Then depressurize the sprayer by pointing it in a safe direction and holding the trigger until all pressure is released. Never point the nozzle toward any person or animal. Always wear ANSI approved safety glasses or goggles when using or servicing this tool. Always wear hearing protection when using or servicing this tool or any air pressure equipment. unPacKinG When unpacking, check to make sure the following parts are included. LVLP Spray Gun Paint Cup If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. reV 05d Page 4 For technical questions, please call 1-800-444-3353. SKU 92841 aSSeMbLy First, prepare your air supply. Quick coupler recommended air Line components regulator with Pressure Gauge Quick coupler air hose on reel Valve FilterOiler coupler Plug tool air compressor coupler Plug 1. This tool requires up to 45 PSI and up to 9 SCFM. Provide yourself with a compressed air supply which will meet these requirements. Air compressors and related supplies are available from Harbor Freight Tools. 2. For best results, arrange your compressed air supply to include a filter and regulator as indicated in the schematic diagram above. The addition of quick connect air valves, reel and other features will enhance your air supply. 3. Attach your air hose (not supplied) to the Spray Gun at the Nipple (36), at the base of the handle. At your option, you may first attach a quick connect valve (not supplied) to the Nipple (36) to attach with your air hose. 4. Nipple (36) Trigger (26) Paint Cup (35) Reservoir Cap (32) Attach the Paint Cup (35) to Reservoir Cap (32) on the bottom of the Spray Gun, as shown in the photo. reV 05d; 09k SKU 92841 For technical questions, please call 1-800-444-3353. Page 5 OPeratiOn 1. Prepare the work piece to be painted according to paint manufacturer’s directions. Prepare your paint mixture according to paint manufacturer’s directions. NOTE: In most cases, paint must be thinned for proper spraying. Be sure to use a thinner recommended by the paint manufacturer. 2. Fill the Paint Cup (35) no more than 2/3 full with your paint mixture. Screw the Reservoir into the Reservoir Cap (32) being sure the Reservoir Seal (33) is in place. 3. Turn on your air compressor, and adjust the regulator to the recommended pressure (20 - 45 PSI). 4. iMPOrtant: Before applying paint to your work piece, test spray a piece of scrap material. In most cases both the paint mixture and spray pattern will have to be adjusted for best results. 5. To spray, squeeze the Trigger (26), as you move the Sprayer past the work material. Release the Trigger (26) at the end of each pass. Repeat until you have proper paint coverage of the work piece. 6. When you have completed painting your project, disconnect the Sprayer from its air pressure source and immediately clean following the directions in the Maintenance section on page 8. Painting tips Successful spray painting is a skill which requires knowledge of your equipment, familiarity with your paint materials and experience. Differences in paints, work materials and environmental conditions make every painting task unique. For best results, practice with your painting mixture on a scrap piece before beginning to paint your work material. It is critical that the surface...
Эта инструкция также подходит к моделям:Распылители краски - CENTRAL PNEUMATIC 92841 (361.11 kb)