Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Overloading can cause the jack to collapse and drop the load. 2. ALWAYS support the vehicle with appropriately rated support stands before working under it. 3. DO NOT attempt to move the vehicle while the jack is in use. 4. Use only on hard level surfaces like concrete or asphalt. Other surfaces are potentially unstable. 5. Center the load on the jack to maintain proper balance and stability. 6. DO NOT use jack if it begins leaking fluid or if it slowly sinks with a heavy load. These are indications that the jack needs to be immediately serviced. Specifications Maximum Lifting Capacity.................. 1,500 Lbs. Lifting Range.............................................6"-18" Weight.....................................................78 Lbs. Operation Pump Handle (Figure 1): To raise the jack, rotate the pump handle clockwise completely, then move the pump handle up and down. To lower the jack, slowly rotate the pump handle counterclockwise. Lock Release Pedal (Figure 1): This jack features a stepped lock system that prevents loads placed on the jack from accidentally dropping. When pushed down, the lock release pedal allows the operator to completely lower the jack and bypass the stepped lock system. Note: The lock pedal will not release if the load binds against the stepped plate. To remove a bind, jack the load one or two pumps. Figure 1. Jack controls. If you need help with the Model H8095, call our Technical Support line at: (570) 546-9663. COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #TR8826 PRINTED IN CHINA Maintenance Keep the hydraulic rams clean and free of any dust, dirt, or foreign debris. Abrasive material stuck to the ram can damage the hydraulic seal when the ram is retracted back into the jack. Regularly wipe the hydraulic rams clean with a lightly oiled rag. The Model H8095 will require hydraulic fluid after long-term use. This will be noticeable if the jack will not reach its maximum height when pumped. Only use a high quality hydraulic fluid. To add hydraulic fluid: 1. Completely lower the jack. 2. Remove the fill plug shown in Figure 2. Figure 2. Fill plug. 3. Add fluid until it reaches the top of the fill plug hole. 4. Replace the fill plug. 5. Test the operation of the jack by pumping it up to the maximum height and applying a load to the saddle. The jack should hold the weight of the load without a sinking or spongy feeling. —If the jack did not perform properly, then air may need to be bled from the pump system. Bleeding the Air If the jack becomes spongy or will not rise when pumped, then air bubbles may be in the hydraulic system. To remove the air bubbles: 1. Remove the fill plug. 2. Rotate the pump handle counterclockwise one full turn. 3. Pump the handle quickly ten times to purge the air from the system. 4. Replace the fill plug and test the operation of the jack. —If the jack did not perform properly, then air may need to be bled from the pump system again. H8095 Parts Breakdown and List REF PART # DESCRIPTION REF PART # DESCRIPTION 21 PH8095021 REAR CASTER 22 PH8095022 FLANGE BOLT M10-1.5 X 20 23 PR01M EXT RETAINING RING 10MM 24 PR09M EXT RETAINING RING 20MM 25 PH8095025 PEDAL ASSEMBLY 26 PH8095026 LIFTING ARM FIXING POLE 27 PH8095027 SOCKET BOLT 28 PLW07M LOCK WASHER 20MM 29 PLN09M LOCK NUT M12-1.75 30 PH8095030 FIXING PIPE 31 PH8095031 HANDLE SOCKET 32 PR39M EXT RETAINING RING 8MM 33 PH8095033 PRESS WHEEL 34 PH8095034 PRESS WHEEL SHAFT 35 PB09M HEX BOLT M8-1.25 X 20 36 PH8095036 PUMP ASSEMBLY 37 PH8095037 HANDLE 38 PH8095038 MACHINE ID LABEL 39 PH8095039 FILL PLUG 1 PR06M EXT RETAINING RING 16MM 2 PW08M FLAT WASHER 16MM 3 PH8095003 FRONT WHEEL 4 PH8095004 BASE ASSEMBLY 5 PH8095005 PLASTIC END CAP 6 PH8095006 SADDLE ASSEMBLY 7 PH8095007 RUBBER CUSHION 8 PH8095008 POLE 9 PN13M HEX NUT M16-2 10 PH8095010 BUSHING 11 PH8095011 RATCHET PLATE 12 PLW10M LOCK WASHER 16MM 13 PH8095013 AXLE COVER 14 PH8095014 SAFETY AXLE 15 PR07M EXT RETAINING RING 18MM 16 PR02M EXT RETAINING RING 14MM 17 PH8095017 SADDLE FIXING AXLE 18 PB06M HEX BOLT M8-1.25 X 12 19 PW01M FLAT WASHER 8MM 20 PH8095020 LIFTING ARM AWARNING The machine ID label warns about hazards and ways to prevent injury. The owner of the jack MUST maintain the original location and readability of the label. If the label is removed or becomes unreadable, contact Grizzly at (800) 523-4777 or to order a new label. I—J TOOL EzJ WEBSITE Buy Direct and Save with Grizzly®- Trusted, Proven and a Great Value! Visit Our Website Today And Discover Why Grizzly® Is The Industry Leader! • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR -OR- - Call Today For A FREE Full Color Catalog...