Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
3. Remove the Air Cap and soak it in solvent until it is clean. Use an old toothbrush and toothpicks to remove any material. Do not use metal objects to clean the Air Cap or you may damage the drilled passages. Inspect the fluid needle and make sure it is not bent. If it is bent, have it replaced by a certified service technician. Warning!! Do not immerse the Spray Gun Body in solvent! 4. Use the appropriate solvent (depending on the material sprayed) to wipe down the Gun body. 5. Always lubricate the Spray Gun after cleaning. You may use a non-silicon oil or a light lubricant on all threaded connections prior to storing the unit. 6. Disposal: After cleaning your Spray Gun, properly dispose of your cleaning solutions according to the solution manufacturer’s direction and local hazardous waste standards. For technical questions, please call 1-800-444-3353; SKU 43760 Page 11 Troubleshooting section at end of manual. Parts List Part Description Part Description 1 Air Cap Set 35 Nipple 2 Fluid Nozzle 36 Fluid Joint 3 Gun Body 37 Screw Cap 4 Trigger Stud 38 Fastener 5 Stop Ring 39 Cup Locking Lever 14 Pattern Control Knob 40 Cup Cover 15 Fluid Control Knob 41 Liquid Tube 16 Needle Spring 42 Cup Cover Gasket 22 Needle Packing Screw 43 Cup 23 Needle Packing Ring 44 Trigger Valve Assembly 24 Air Valve Packing Ring 45 Fluid Control Assembly 32 Trigger 46 Pattern Control Assembly 33 Air Inlet Screw 47 Vinyl Vent Tube 34 Air Inlet 48 Vent Port PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. REV 10/03; 08/05 For technical questions, please call 1-800-444-3353; SKU 43760 Page 12 Troubleshooting section at end of manual. Assembly Diagram 46 2 1 5 4 6 7 8 9 1011 12 14 13 13 8 5 2019 18 45 17 16 15 33 34 3532 31 30 29 28 44 27 26 242524 23 22 3 36 37 38 39 40 41 42 43 0 47 48 REV 10/03; 08/05 For technical questions, please call 1-800-444-3353; SKU 43760 Page 13 Troubleshooting section at end of manual. IMPORTANT: Improper cleaning is a common reason for the unit not to work properly. Most problems can be avoided or remedied with prompt, thorough cleaning. Troubleshooting Spray Pattern Diagnosis The Patterns below resemble symptoms of spray pattern problems. Please refer to the accompanying possible problems if you are experiencing similar difficulties. The solution to each problem follows the problem in parentheses. Problem 1: 1. The Pattern Control Knob (14) is partially closed. (Open Pattern Control Knob (14).) 2. The material is too thick. (Thin material according to the manufacturer’s instructions.) 3. The air pressure is too low. (Increase air pressure within the Maximum PSI (55).) Problem 2: 1. High air pressure. (Reduce air pressure.) 2. Not enough fluid. (Increase fluid.) 3. Pattern Control Knob (14) open too much. (Partially close Pattern Control Knob (14).) Problem 3: 1. Air Cap plugged. (Clean the Air Cap.) 2. Air cap loose or dirty seat. (Clean and tighten.) 3. Dried material on fluid tip. (Use a nonmetallic point to clean the Air Cap.) Problem 4: 1. Dirt on one side of the fluid tip. (Clean the fluid tip.) 2. Holes on one side of the Air cap are plugged. (Clean the Air cap with a nonmetallic point.) If the steps above do not solve the problem or if the repairs involved are too complex, contact a qualified technician. SKU 43760 For technical questions, please call 1-800-444-3353. Page 14 IMPORTANT: Improper cleaning is a common reason for the unit not to work properly. Most problems can be avoided or remedied with prompt, thorough cleaning. Troubleshooting (continued) Problem Cause Solution 1. Low material level 1. Refill 2. Cup tipped too far 2. Hold upright Sputtering Spray 3. Clogged Air Vent 4. Loose fluid inlet connections 3. Clean vent hole 4. Tighten 5. Dry or loose fluid needle Packing Nut 5. Lubricate and/or tighten 6. Loose/damaged fluid tip/seat 6. Adjust or replace Will Not Spray 1. No pressure at gun 2. Fluid control not open enough 3. Fluid too thick 1. Check air hoses 2. Open fluid control 3. Thin fluid or increase pressure (within Maximum range) Overspray 1. Improper application speed 2. Improper distance from workpiece 3. Too much pressure 1. Move moderately and paralle...
Эта инструкция также подходит к моделям:Распылители краски - 43760 (263.9 kb)