Оценок - , средний балл: ( )

Инструкция по эксплуатации Hitachi, модель 91011

Производитель: Hitachi
Размер: 813.97 kb
Название файла: 229d5d31-e508-4987-82c2-547e2856a2e5.pdf

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

5. To adjust the spray pattern, set up a piece of scrap material to practice on. While practicing on the scrap material, check to see that the material you are spraying has the appropriate consistency. If it appears to thin, add a very small amount of thinner (not included). BE CAREFUL when thinning. Proceed slowly, adding very minimal amounts. NEVER exceed the manufacturer’s thinning recommendations. Fan Direction and Pattern Adjustment Fan Direction To change the direction of the fan from horizontal to vertical, loosen the Lock Ring and turn the Air Cap (46) 90 degrees. After the adjustment, tighten the Lock Ring by hand. See FIGURE 4 below. FIGURE 4 Horizontal Fan Vertical Fan Air Cap Lock Ring SKU 93312 Page 8 For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. Pattern Adjustment Warning!! Never exceed the Maximum Inlet PSI of 70 PSI. 1. Remember that the air pressure feeding the gun should be set to 10-30 PSI, using the Air Regulator (24). 2. To set the pattern size specific to the job, use the Pattern Control Knob (65) (see FIGURE 1 on page 6). By turning it counterclockwise (all the way open), the pattern will flatten. Turn the Pattern Control Knob (65) clockwise for a round pattern. See FIGURE 5 below. FIGURE 5 Flat/Open Round/Closed 3. Open the Fluid Outlet (39)and Fluid Flow Knob (11). Turn the Fluid Control Knob (59) clockwise until it is fully closed. See FIGURE 1 on page 6. 4. After setting up a piece of scrap material, squeeze the Trigger (52) in short bursts while turning the Fluid Control Knob (59) counterclockwise and observe the spray patterns until you see the pattern you want. Also, look at the pattern for consistency. Too much air may cause the spray to come out too fine. Reduce the air pressure or allow more material to come out by opening the Fluid Control Knob (59). If the spray appears too thick (you see globs of paint), close down the Fluid Control Knob (59) slowly, checking the mixture after each adjustment. See FIGURE 6 below. FIGURE 6 Too Fine (Loosen) Too Coarse (Tighten) Correct SKU 93312 Page 9 For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. Techniques Note: Before spraying, mask all objects you do not want sprayed and lay cloths (not included) on the floors. 1. Always keep the gun at right angles to the workpiece (See FIGURE 7). Pull the Trigger (52) slowly and move the Spray Gun in parallel strokes to the object being painted. Keep the distance from the object being painted at 6” to 9”. This may slightly differ depending on the flow adjustment and the material being sprayed. Do not stop the gun movement while spraying. If you stop the gun for even just a slight pause while spraying, the paint will build up and run down the workpiece. FIGURE 7 (Heavier coat on one side, uneven coverage) Incorrect (Even coverage) Correct (90o) 2. To ensure you don’t allow paint to build up, start moving the Spray Gun before you Squeeze the Trigger (52). When you are finished spraying, release the Trigger (52) before you stop moving the Spray Gun. Doing so will eliminate distinct overlaps, producing a blended (feathered) affect. See FIGURE 8 below. EndBegin ReleaseSqueeze Stroke Trigger (52) FIGURE 8 Trigger (52) Stroke (Top View) Note: The speed of the stroke, the adjustment of the Fluid Control Knob (59), and the distance from the workpiece, will determine how much paint is being applied. To get the best results, try to apply two thin coats of paint versus one thick coat. 3. Clean out the gun thoroughly after EVERY use, according to the instructions found on the next page. SKU 93312 Page 10 For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. Maintenance SOLVENT SELECTION Always follow the paint manufacturer’s recommendations for cleaning, solvent type, and disposing of used solvent. Latex Paints: Use warm, soapy water. IMPORTANT: Do not use mineral spirits on latex paints or the mixture will congeal making it very difficult to remove. Oil Based Paints: Use mineral spirits. IF A FLAMMABLE SOLVENT NEEDS TO BE USED, ADHERE TO THE FOLLOWING: 1. Follow all of the solvent manufacturer’s clean up instructions and safety precautions at all times. 2. Always flush the Spray Gun a full hose length from the air compressor. 3. If collecting flushed solvents into a metal container, transfer into a larger nonmetal container, and flush the metal container. 4. Work far away from any ignition sources in a vapor free area. After each use: 1. Empty the Paint Cup (16) and clean it with the solvent. 2. Fill the Paint Cup (16) with solvent and spray it through the Gun into a container, while shaking the gun. Once the Paint Cup (16) is empty, repeat the process until the solvent comes out clean. Disconnect from the air source. After disconnecting, be aware that air pressure may still remain in the Spray Gun. Point the Gun into the spent solvent container and squeeze the Trigger again ...