Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm. Wash hands after handling. CAUTION RULES FOR SAFE OPERATION Before assembling and operating your sprayer, read all instructions thoroughly. When working with equipment under pressure, safety precautions must always be carefully observed, including the following: • NEVER spray flammable materials or pressure and gas producing chemicals. • ALWAYS read chemical label before filling sprayer as some chemicals may be hazardous when used with this sprayer. • ALWAYS wear goggles, gloves, a long-sleeve shirt, long pants, and full foot protection when spraying. Work in a ventilated area or outdoors. • PRE-USE CHECK: Before each use check tightness of hose nut to be sure hose is securely attached to the shut-off assembly. Insure hose is securely attached to the tank by tightening hose clamp if necessary. Insure that all nozzle and wand connections are tight. Insure the large pump clamp is tight. Insure the 2 bolts used to attach the pump lever to the pump shaft are tight. • DO NOT leave a pressurized sprayer in the hot sun or anywhere near a heat source. Heat can produce pressure to build up causing sprayer to ignite or explode resulting in injury or death. • NEVER pressurize sprayer by any means other than the original pump. Over pressurizing can cause sprayer to explode resulting in injury or death. • DO NOT attempt to modify or repair this product except with original manufacturer’s parts. NOTE: The tank and hose may have residual water in it due to quality testing performed on the sprayer. 1E APPLICATIONS & USE FOR YOUR SPRAYER Avoid using a sprayer for general cleaning purposes if plant protection or herbicide chemicals have already been used in the sprayer. If a sprayer has been used for plant protection or as an herbicide, clean the sprayer completely (see cleaning section) before using. Plant Food: Use different spray patterns for optimum foliage feeding or for fungicide and pesticide application. Herbicides: Reduce weeds and unwanted plants but avoid using the same sprayer for plant feeding or protection without thoroughly cleaning (see cleaning section) the sprayer first. General Household Use: Apply detergents, vinegar, cleaning solutions, warm water (do not exceed 120°F/49°C) or nontoxic household cleaning chemicals for carpets, floors, walls, glass, counter tops and ceilings. DO NOT use sprayer that has been used with herbicides, pesticides or other toxic chemicals for household applications. General Outdoor Use: Use the sprayer for cleaning windows or with a detergent for general purpose cleaning. Other applications include wood preservatives, waxes, water proofing, and diluted household bleach (max. 1 part household bleach to 9 parts water solution). SPRAYER COMPONENTS & USE INFORMATION NOZZLE ASSEMBLY Figure 1-2 Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5). Unscrew the retaining nut (2). Push the nozzle body (3) with the nozzle gasket (4) out of the retaining nut (2). To reinstall the nozzle, reverse the above instructions. Figure 3 Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut. To reinstall the nozzle, reverse the above instructions. 3. Nozzle Body 2. Retaining Nut 5. Elbow 4. Nozzle Gasket Figure 1 Figure 2 Figure 3 1. Poly Nozzle Cap 1. Brass Nozzle Cap Elbow Nozzle Gasket Fan Nozzle Tip Retaining Nut 2. Retaining Nut 3. Nozzle Body 4. Nozzle Gasket 5. Elbow WAND ASSEMBLY 1. Make sure the o-ring is installed on the end of the wand. Insert the wand into shut-off valve. 2. Turn and tighten the retaining nut clock-wise onto the shut-off valve. Wand Shut-off Valve Retaining Nut O-ring 2E SPRAYER COMPONENTS & USE INFORMATION, Continued INSTALLING THE PUMP HANDLE The pump handle can be mounted on either side of the pump shaft (A). To install the pump handle place the handle (C) over the shaft (A) aligning the pump handle hole and shaft hole. Push the straight side of the cotter pin (B) through the aligned hole as shown in figure 1 thru 3. There are holes in the pump handle to allow for either left(fig.4) or right (fig.5) hand mounting. A C B Figure 1 Cotter Pin Figure 2 Line up holes Figure 3 Slide pin through holes. Pull up Rotate 180. Set into slot Pump Handle Positioned For Use (right hand shown) STOWAWAY PUMP HANDLE Figure 4 Figure 5 Left Hand Right Hand INSTALLING THE WAND CLIP SHOULDER STRAP The wand can The top of the shoulder straps are be attached to attached to the tank. Attach the the pump handle using lower end of the straps by the wand clip. clipping the strap hooks to the metal frame between where the frame exits the tank and curves around. NOTE: If your straps become contaminated with dirt or chemicals, wash with mild soap and water and let dry overnight. If this does not remove the contamination, repl...