Оценок - , средний балл:
(
)
)
Производитель: Philips
Размер: 259.39 kb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
1. Use only the battery(ies) instructed. USER MANUAL / MODE Multi channel cordless phone / Telephone sans fils multi-canal TD 9220 2. Do not dispose of the battery(ies) in a fire. The cell may explode. Check with local codes for possible special disposal instructions. 3. Do not open or multilate the battery(ies). Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. 4. Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns. 5. Charge the battery(ies) provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual. Installation: 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Use caution when installing or modifying telephone lines. Warning: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE ( ii) 1 Chose a spot near an electric 2 Install the handset antenna Slide the metal tip of the handset antenna into the opening in the top of the Turn the antenna clockwise to make sure the tip is set in place, and continue until it is sung against the top of the handset. Do not over tighten. 3 Install the handset battery • Remove the battery compartment cover on the handset by pressing on the identation and sliding the cover downward • Plug the battery pack cord into the handset, and tuck the cords in next to the battery • Replace the cover by sliding it on its track 4 Set Tone or Pusle dialing • Press Memory button • Press Recall button • Press for Tone, or for Pulse • French version do not have this function 5 Connect the telephone line cord • Plug one end of the telephone line cord into the jack on the top of the base • Plug the other end into a modular telephone jack 6 Mount the base on the wall (wall installation only) • Mark and drill two holes in a wall stud, 3 5/16" apart • Use two wall screws, leaving about 1/4" free of the wall • Plug one end of the telephone line cord into the jack on the top side of the base • Plug the other end into a modular telephone jack • Mount the base unit on the wall by aligning the two holes on the back with screws • Slide the base unit down in place 7 Plug the power cord • Plug the one end of the power cord into the jack on the top side of the base • Plug the AC adapter on the power cord into an electric outlet 8 Charge the handset battery pack for at least 12 hours Place the handset in the base, the CHARGE light on the base goes on to show the handset is in the right position to charge the battery pack. 9 Check for dial tone After the battery pack is charged, pick up the handset and extend the base antenna. Check for dial tone by pressing the , the IN USE light on the base should go on, and you should hear a dial tone. 10 Set TBR time The flash time is pre-set for end users, users do not switch it under normal usage. The TBR times switch is located on the top side of the base. Three flash time, A-100ms, B-270ms and C620ms are available for different telephone network system. Select suitable flash time if necessary. ! CAUTION: Use only the AC power adapter supplied with this telephone. Power supply 92201160DV Input : 230V AC 50Hz 45mA Output : 9V…220mA 1.98VA 11V…60mA 0.66VA ( 1) ENG The handset and base can communicate over only a certain distance - which can vary with the locations of the base and handset, the weather, and the construction of your home or office. For best performance, make sure the base antenna is fully upright. If the handset is moved to a point where the base and handset can longer you are “out of range”. When you try to make a call, the handset will beep to indicate that are out of range. If you receive a call while you are out of range, the handset might not ring - or if it does the call might not connect when you press . Move closer to the base, then press to answer the call. If you move out of range during a phone conversation, you may be disconnected. Changing Channels This cordless telephone has multi channels available for maximum performance. If you notice noise or interference while using the handset: 1. Press . 2. If the interference doesn’t clear, continue to press until you find a clear channel. - OR Move closer to the base and press . NOTE: You must be in range to change channels. Memory This cordless phone can store 10 telephone numbers that you can dial by pressing and one of the number buttons. Additionally, you can store a memory number in the memory location. Storing Memory Numbers 1. Make sure the handset is off. 2. Press . 3. Enter the phone number (up to 20 digits) . 4. Press . 5. Press any number bu...
Эта инструкция также подходит к моделям:Радиотелефоны - TD9220 (259.38 kb)