Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
1. From the previous setting, or press until hear the VoiceHelp: 2. The display will show “-“. 3. Press . 4. Record the message or sound after the beep. 5. You will have four seconds for your programmable ringer.The display will count down from 4. 6. Press when finished. The recording will then playback. 7. Press if you want to replace the previous recording. 8. Press to confirm and go to next setting. Setting the Dialling Mode You can change your dial mode to either Tone or Pulse ( , ) with the switch on the lower right hand side of the handset. ( See Fig 1, 2 ) Setting the ringer volume You have the ability to set your ringer to either Hi, Low or Off ( , , ) with the switch on the upper right hand side of the handset. Note: The ringer LED will light up when there is an approach of an incoming call, even when the ringer mode is set in the “off” position. Setting the ringer melody You can select the ringer frequency in Slow, Normal or Fast mode. Note: The ringer will default to the Normal mode setting if the telephone is disconnected from the wall Setting the volume for the Earpiece You can control the loudness of the earpiece by pressing Receiver Volume Control button. (See Fig 1, 4 ) Press - to decrease the volume. Press , to increase the volume. Note: After the phone is returned to the base, the volume setting will return to its original setting. or or USER MANUAL Permanent memories: no tape, no battery Cuckoo new-message audio reminder One-touch Do Not Disturb function Recordable ringer Built-in selectable ringing melodies Do Not Disturb Ringer Light Indicator Digital Receiver Volume Control Plug & Play with built-in OGMs 14 minutes memory capacity 3 Direct Memories and 10 Indirect phone memories Introduction Thank you for buying the Elegance 99 from Philips. You are guaranteed to experience the efficiency and quality set by Philips standard. In this package you will find the following: • one base unit • one handset • one user manual • one line cord • ac adaptor • one telephone memo card • remote control card • two wall mount screws Installation 1. Connect the handset cord to the socket of answering machine ( ). 2. Connect the answering machine to the telephone cord ( ). 3. Connect the AC adaptor plug to AC mains outlet [ AC ( 9V~) ] 3.1 You will hear the VoiceHelp 3.2 Just by means of this PLUG & PLAY action, simultaneously, ELEGANCE 99 will take care your incoming messages. Please refer to the section: Select Your Answering Mode. Store Store 74mm 1. Ringer Hi/Low/Off switch 6. Store Button 2. Tone/Pulse switch 7. Flash/Recall Button 3. Ringer LED 8. Indirect Memory (shift) Button 4. Receiver Volume Control 9. Direct Memory M1, M2, M3 5. Redial/Pause Wall Mounting Fig. 1 P R 1 2 3 4 5 6 7 8 9 0 # M1 M2 M3 0 9 2 8 5 3 4 1 6 7 ABC DEF GHI JKL MNO PQRS TUV WXYZ The Telepone Part Location of buttons, controls and operating elements Storing a number into direct dial memory The Elegance 99 has the convenience of 3 direct dial memories. 1. Same as the procedures as stated in above. 3. Press or to change the setting then the display will show “0-”. 4. Press to confirm and go to next setting. Setting the Ringer On / Off ELEGANCE 99 provides two extra pre-recorded and one user programmable ringers for the incoming calls. You can switch on the ringer function and then select one of the extra ringers to replace the ringer on the parallel phone. To switch the ringer on: 1. From the previous setting, or press until hear the VoiceHelp: 2. The display will show “0-”. 3. Press or then the display will show “On” 4. Press to confirm and go to next setting. To switch the ringer off: Record Ringer Select Ringer or or Ringer OFF 1. From the previous setting, or press until hear the VoiceHelp: 2. Press or to select your desired ringer from the two pre-recorded ringers and your personalized. 3. Press to confirm and go to next setting. Note: In order to select into your own recorded ringer, you need to record it first. - The pre-recorded ringers are shown in the display as : n1 and n2 - Your personalized ringer is shown as : nP on the display. - There is a maximum duration for the recorded ringer of 4 seconds. Selecting Ringer or 1. From the previous setting, or press until hear the VoiceHelp: (The Answering Machine is defaulted at Answer Delay 3. It will answer the incoming call after at the third ring.) 2. Press or to select the desired Answer Delay: 2, 3, 4, 5 or “E” “E” stands for Economy mode (Toll Save). For this setting, the Answering Machine will pick up the incoming call at the second ring (Answer Delay = 2) if there are new messages in the machine. Otherwise, in case of no new message, it will pick up the line at the fifth ring (Answer Delay = 5). It allows the user to call back his answering Machine and identify if there is any new message at the third and fourth rings without actually connect the call. 3. Press to confirm and go to next setting. Answer Delay 3 Setting Answer Delay To set the number of rings before ...