Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Advanced settings 13.8 Reset Unit You can reset your phone to its default settings with this feature. (see 13.15 “Default Settings”) Caution Upon reset, all your personal settings, call log and redial list entries will be deleted and the phone will return to its default settings. However, your phonebook will remain unchanged after reset. Note You may have to configure your phone once again. 1 Press m in idle mode, scroll n to Advanced Set and press o Select. 2 Scroll n to Reset and press o Select. 3 Reset? is displayed on the screen. Press o OK to confirm. • A validation tone is emitted. • The unit is reset to its default settings. (See section 13.15 below.) 13.9 Set Area Code This feature is useful when you have subscribed to Caller Line Identification service. It allows you to set an area code in your phone. Once the local area code is set, the phone automatically filters the area code for all incoming calls, by removing the area code for local calls and retaining the area code for calls from other areas. If it is a local call, then only the phone number of the caller is displayed during an incoming call or when you call the number from the call log. If it is a long distance call, then both the area code and phone number will be displayed in a proper format to be dialed out directly from the call log, or saved into the phonebook. Note You can enter 3 digits for the area code. You need to subscribe to Caller Line Identification service to be able to see the caller’s number or name in the call log. See 8.1.4 “Call from the call log” for details. 1 Press m in idle mode, scroll n to Advanced Set and press o Select. 2 Scroll n to Area Code and press o Select. 3 Scroll n to select Line 1 or Line 2 and press o Select. 4 Area Code will appear in the display. Input your area code and press o OK to confirm. • A validation tone is emitted and the screen returns to the Advanced Set menu. 13.10 Set Auto Prefix This feature allows you to define a prefix number to be added to the beginning of a number during predialling (see “Predialling” - section 8.1.1). You may also use this feature to add a detect string to match and replace the first few digits of the number during predialing. Advanced settings You can enter up to a maximum of 5 2 Scroll n to Flash Time and press digits for the detect string and 10 digits for the auto prefix number. 1 Press m in idle mode, scroll n to Advanced Set and press o Select. 2 Scroll n to Auto Prefix and press o Select. 3 Scroll n to select Line 1 or Line 2 and press o Select. 4 Detect Digit: is displayed on the screen. Enter a detect string number (maximum 5 digits) and press o OK to confirm. 5 Prefix: is displayed on the screen. Enter the prefix number (maximum 10 digits) and press o OK to confirm. • A validation tone is emitted and the screen returns to the Advanced Set menu. Note If no detect string (blank) is entered, the prefix number will be automatically added to the predial number after t is pressed. For numbers starting with *, # or P, the prefix number will not be added to the predial number after t is pressed. 13.11 Change Flash time Flash time is the time delay by which the line will be disconnected after you press the t key. It can be set to short or long. The default value is Long. 1 Press m in idle mode, scroll n to Advanced Set, and press o Select. o Select. 3 Scroll n to Short or Long and press o Select to confirm. • A validation tone is emitted and the screen returns to the Advanced Set menu. Note The use of your SE659 cannot be guaranteed on all PABX. 13.12 Change the Dial Mode The default value for dial mode that is preset in your handset should be the best suited for your subscribed network and therefore you should not need to change it. 1 Press m in idle mode, scroll n to Advanced Set, and press o Select. 2 Scroll n to Dial Mode and press o Select. 3 Scroll n to select Line 1 or Line 2 and press o Select. 4 Scroll n to Tone or Pulse and press o Select to confirm. • A validation tone is emitted and the screen returns to the Advanced Set menu. 13.13 Set First Ring Detection First ring detection allows the phone to ring upon reception of the first ring signal. It is recommended that you set first ring detection Off if you subscribe to caller line identification service. (When using personalized phonebook Advanced settings melodies, this will prevent a normal ring tone from sounding before a melody starts playing.) If you do not subscribe to caller line identification service, it is recommended that you set first ring detection On. (See Section 10.4.) 1 Press m in idle mode, scroll n to Advanced Set, and press o Select. 2 Scroll ntoFirst Ring and press o Select. 3 Scroll n to select Line 1 or Line 2 and press o Select. 4 Scroll nto On or Off and press o Select to confirm. • A validation tone is emitted and the screen returns to the Advanced Set menu. Note The default setting for first ring detection is On. The setting automatically switches to Off when you receive a call...