Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
This handset is an accessory cordless handset, for use with Panasonic base units KX-TG5200/KX-TG5202/KX-TG5210/KX-TG5212/KX-TG5213/KX-TG5230/KX-TG5240/ KX-FPG391. This installation manual only describes the steps necessary to start up the handset. Please read the base unit operating instructions for further details. Accessories (included) For extra orders, call 1-800-332-5368. ACharger Unit . . . . . . . . . . . . . . . . . . . . . . .one ABattery . . . . . . . . . . . . . . . . .one Charger Order No. PQLV30024ZM Order No. HHR-P104 AC Adaptor Order No. KX-TCA1-G (KX-TCA1) ABelt Clip . . . . . . . . . . . . . . . .one AHandset Cover. . . . . . . . . . . . . . . . . . . . . .one Order No. PQKE10377Z1 Order No. PQKK10142Z1 Installation Connect the Charger unit Power Outlet (AC 120 V, 60 Hz) AC Adaptor • USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. KX-TCA1-G). • The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) Install the battery Insert the battery (1), and press it down until it snaps into the compartment (2). Close the cover. 1 2 For assistance, please call: 1-800-211-PANA(7262) – 1 – PQQX14000ZA S0104-0 Charging the battery Place the handset on the charger and charge for 6 hours before initial use. • The unit beeps once, the CHARGE indicator lights and “Charging” is displayed. • When the battery is fully charged, “Charge completed” is displayed if there are no new calls in the Caller List. • Recharge the battery when: —“Recharge battery” is displayed on the handset, —“3” flashes, or — the handset beeps intermittently while it is in use. CHARGE Indicator • If the battery has been discharged, the handset will display “Charge for 6 HRS” and “4” when you place the handset on the charger. The handset will not work unless the battery is charged. Continue charging. Handset battery information After your Panasonic battery is fully charged, you can expect the following performance: Charge Contacts Operation Operating time While in use (TALK) Up to 5 hours While not in use (Standby) Up to 11 days While using the Clarity Booster feature Up to 3 hours • Clean the charge contacts of the handset and the charger with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly. Belt Clip You can hang the handset on your belt or pocket using the included belt clip. To attach the belt clip To remove the belt clip While pressing the top of the clip (1), BApull the right edge in the direction of the arrow (2). – 2 – Registration This cordless handset must be registered to a KX-TG5200/KX-TG5202/KX-TG5210/ KX-TG5212/KX-TG5213/KX-TG5230/KX-TG5240/KX-FPG391 base unit. The handset will be assigned the extension number at registration. Only one handset can be registered at a time. Charge the battery fully. Make sure the base unit and the other handsets are not being used. Have both the handset and base unit nearby during registration. OKOK BACKBACK CHARGE Indicator *LOCATOR Button To operate “ ”, press the right soft key. OK1Press LOCATOR on base unit for 3 sec. Then press OK [-] L • Base unit model shown here is KX-TG5240. * The location of the LOCATOR button varies by base unit model. KX-TG5200/KX-TG5202: LOCATOR [], [], [], [] or [ ] KX-TG5210/KX-TG5212/KX-TG5213: LOCATOR/INTERCOM [], [], [], [] or [ ] KX-TG5230/KX-TG5240/KX-FPG391: [LOCATOR/INTERCOM/TRANSFER] The handset display shows the instructions as shown on the Press LOCATOR right. on base unit for 3 sec. Then press OKL OK 1 Base unit: Press and hold the *LOCATOR button for 3 seconds. • The CHARGE indicator flashes. After the CHARGE indicator starts flashing, the rest of the procedure must be completed within 1 minute. • On the KX-FPG391, “HS REGISTRATION” is displayed. 2 Handset: (1) Press the soft key ( ). (2) Wait until a long beep sounds and the display shows the new extension number. • Registration is complete. OK SPIPRIVACY1Handset Registering IN USE [-] SPIPRIVACY1Handset [2] Registered IN USE [2] Ex. Extension number 2 • The registered number “[1]” to “[4]” is shown on the top right of the display. • You can stop registration by pressing [OFF] on the handset and pressing the *LOCATOR button on the base unit. • If you try to register this handset to the KX-TG6500 base unit, “Wrong handset Refer to manual” is displayed. The base units for this handset are mentioned above. To cancel the handset registration, please see your base unit Operating Instructions. For assistance, please call: 1-800-211-PANA(7262) – 3 – Selecting the display language You can select either “English” or “Spanish” as the display language. The factory preset is “English”. Press [MENU] N[d] or [B] to select “Initial setting” N Soft key ( ) N N[d] or [B] to select “Change language” NSoft key ( SELECT SELECT ) N Soft key ( ) to select “Espanol”, or soft key ( ENGLISH ) to select “English” N Soft key ( GUARDAR ) for Spanish, or soft key ( SAVE )...