Оценок - 4, средний балл: 3.8
(
)
)
|
К этому устройству также есть другие инструкции:
Радиотелефоны - KXTG9322 (2.04 mb)
Радиотелефоны - KXTG9322 (2.24 mb)
Фрагмент инструкции
To protect your privacy/confidentiality, we recommend that you erase information such as phonebook or caller list entries from the memory before you dispose of, transfer, or return the product. Notice ENERGY STAR As an ENERGY STAR® Partner, Panasonic has determined that this product meets the ENERGY STAR guidelines for energy efficiency. ENERGY STAR is a U.S. registered mark. Specifications ¦ Standard: DECT 6.0 (Digital Enhanced Cordless Telecommunications 6.0) ¦ Frequency range: 1.92 GHz to 1.93 GHz ¦ RF transmission power: 115 mW (max.) ¦ Power source: 120 V AC, 60 Hz ¦ Power consumption: Base unit: Standby: Approx. 1.4 W Maximum: Approx. 4.2 W Charger: Standby: Approx. 0.6 W Maximum: Approx. 3.6 W ¦ Operating conditions: 0 °C – 40 °C (32 °F – 104 °F), 20 % – 80 % relative air humidity (dry) Note: L Design and specifications are subject to change without notice. L The illustrations in these instructions may vary slightly from the actual product. For assistance, please visit Getting Started Getting Started Setting up Connecting the AC adaptor LUse only the supplied Panasonic AC adaptor PQLV219. ¦ Base unit Press plug firmly. (120 V AC, 60 Hz) Hook Correct Wrong ¦ Charger Hooks (120 V AC, 60 Hz) Connecting the telephone line cord Refer to one of the following methods depending on your situation: – To connect to a 2-line telephone jack: page 8 – To connect to 2 single-line telephone jacks: page 9 – If you use the unit as a single-line telephone only: page 9 Connect the telephone line cord until it clicks into the base unit and telephone line jack. To connect to a 2-line telephone jack “Click” “GREEN” plug 4-wire cord To 2-line telephone jack (RJ14C) For assistance, please visit Getting Started Getting Started To connect to 2 single-line telephone jacks “Click” “Transparent” plug “GREEN” plug To single-line telephone jacks (RJ11C) Line 1 2-wire cord Line 2 If you subscribe to a DSL/ADSL service Please attach a DSL/ADSL filter (contact your DSL/ADSL provider) to the telephone line between the base unit and the telephone line jack in the event of the following: – noise is heard during conversations. – Caller ID features do not function properly. To connect to a 2-line telephone jack For this connection, please purchase a Panasonic 2-line splitter (page 4). Example: DSL/ADSL line is line 2 “Click” 4-wire cord If you use the unit as a single-line telephone only Be sure to connect the telephone line cord to LINE 1/2. Change the line selection mode from “Auto” to “Line1” (page 14). “Click” “Transparent” plug “GREEN” plug To 2-line telephone jack (RJ14C) 2-line splitter “Click” 2-wire cord “Transparent” plug To single-line telephone jack 4-wire cord (RJ11C) DSL/ADSL filter* “Click” 2-wire cord Note: L“Check tel line 2” is displayed *DSL/ADSL filter (not supplied) is on the unit. To erase it, see page 39. required if you have DSL/ADSL service. For assistance, please visit Getting Started Getting Started To connect to 2 single-line telephone Battery installation jacks LUSE ONLY Ni-MH batteries AAA Example: DSL/ADSL line is line 2 (R03) size. LDo NOT use Alkaline/Manganese/ “Click” Ni-Cd batteries. LConfirm correct polarities (S, T). “Transparent” plug “GREEN” plug To single-line telephone jacks (RJ11C) Line 1 4-wire cord 2-wire cord Line 2 “Click” DSL/ADSL filter* *DSL/ADSL filter (not supplied) is required if you have DSL/ADSL service. Rechargeable Ni-MH ONLY Battery charge Charge for about 7 hours. LWhen the batteries are fully charged, “Charge completed” is displayed. Confirm “Charging” is displayed. For assistance, please visit Getting Started Getting Started Note when setting up Note for connections LThe AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) LThe AC adaptor should be connected to a vertically oriented or floor- mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected. During a power failure The unit will not work during a power failure. We recommend connecting a corded-type telephone (without AC adaptor) to the same telephone line or to the same telephone line jack using a Panasonic T-adaptor (page 4). Emergency power can be supplied to the unit by connecting a Panasonic battery back-up power supply noted on page 4. Note for battery installation LUse the supplied rechargeable batteries. For replacement, we recommend using the Panasonic rechargeable batteries noted on page 4, 6. LWipe the battery ends (S, T) with a dry cloth. LAvoid touching the battery ends (S, T) or the unit contacts. Note for battery charge LIt is normal for the handset to feel warm during charging. LClean the charge contacts of the handset, base unit, and charger with a soft and dry cloth once a month. Clean more often if the unit is exposed to grease, dust, or high humidity...