Оценок - 5, средний балл: 4.6
(
)
)
|
Фрагмент инструкции
Changing the handset name Each handset can be given a customized name (“Bob”, “Kitchen”, etc.). This is useful when you make intercom calls between handsets. You can also select whether or not the handset name is displayed in standby mode. The default setting is “Off”. If you select “On” without entering any handset name, “Handset 1” to “Handset 6” is displayed. 1 {MENU} i {#}{1}{0}{4} 2 Enter the desired name (max. 10 characters; see the character table, page 20). L If not required, go to step 3. 3 {SAVE} 4 {V}/{^}: Select the desired setting. i {SELECT} 5 {SELECT} i {OFF} Call block (Caller ID subscribers only) This feature allows the unit to reject calls when: – the unit receives a call from a phone number stored in the call block list as unwanted (“Storing unwanted callers”, page 30). – the unit receives a call without phone number (“Block calls without phone number”, page 31). When a call is received, the unit rings for a short time while the caller is being identified. If the phone number matches an entry in the call block list, the unit sends out a busy tone to the caller, and then disconnects the call. Important: L When the unit receives a call from a number that is stored in the call block list or a call without a recognized phone number, the call is logged in the caller list (page 34) with $ after the call is disconnected. Storing unwanted callers You can store up to 30 phone numbers in the call block list by using the caller list or by entering the numbers directly. Important: L We recommend storing 10 digits (including an area code). If only 7 digits are stored, all numbers that have the same last 7 digits will be blocked. ¦ From the caller list: 1 {<} CID 2 {V}/{^}: Select the entry to be blocked. L To edit the number, press {EDIT} repeatedly until the phone number is shown in the 10-digit format. 3 {SAVE} 4 {V}/{^}: “Call block” i {SELECT} 5 {V}/{^}: “Yes” i {SELECT} 6 Edit the phone number if necessary (24 digits max.). 7 {SAVE} i {OFF} ¦ By entering phone numbers: 1 {MENU} i {#}{2}{1}{7} i {ADD} 2 Enter the phone number (24 digits max.). L To erase a digit, press {CLEAR}. 3 {SAVE} i {OFF} For assistance, please visit Programming Block calls without phone number You can reject a call without phone number including “Out of area”, “Private caller”, or “Longdistance”. 1 {MENU} i {#}{2}{4}{0} 2 {V}/{^}: Select the desired setting. i {SAVE} i {OFF} Viewing/editing/erasing call block numbers 1 {MENU} i {#}{2}{1}{7} 2 {V}/{^}: Select the desired entry. L To exit, press {OFF}. 3 To edit a number: {EDIT} i Edit the phone number. i {SAVE} i {OFF} To erase a number: {ERASE} i {V}/{^}: “Yes” i {SELECT} i {OFF} Note: L When editing, press the desired dial key to add, {CLEAR} to erase. L When viewing, “Block w/o num” is displayed if the block calls without phone number feature is turned on. To turn the feature off: {ERASE} i{V} i {SAVE} i {OFF} Registering a unit Operating additional units Additional handsets Up to 6 handsets can be registered to the base unit. Important: L See page 6 for information on the available model. Registering a handset to the base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset. 1 Handset: {MENU} i {#}{1}{3}{0} 2 Base unit: ¦ KX-TG6511 series: page 3 Press and hold {LOCATOR} for about 5 seconds. (No registration tone) ¦ KX-TG6521/KX-TG6531/ KX-TG6541 series: page 3 Press and hold {LOCATOR} for about 5 seconds until the registration tone sounds. L If all registered handsets start ringing, press the same button to stop. Then repeat this step. L The next step must be completed within 90 seconds. 3 Handset: Press {OK}, then wait until a long beep sounds. Note: L While registering, “Base in registering” is displayed on all registered handsets. L When you purchase an additional handset, refer to the additional handset’s installation manual for registration. For assistance, please visit Programming Deregistering a handset A handset can cancel its own registration (or the registration of another handset) that is stored to the base unit. This allows the handset to end its wireless connection with the system. 1 {MENU} i {#}{1}{3}{1} L All handsets registered to the base unit are displayed. 2 {V}/{^}: Select the handset you want to cancel. i {SELECT} 3 {V}/{^}: “Yes” i {SELECT} 4 {OFF} For assistance, please visit Caller ID Service Using Caller ID service Important: L This unit is Caller ID compatible. To use Caller ID features, you must subscribe to a Caller ID service. Contact your service provider/ telephone company for details. Caller ID features When an outside call is being received, the caller’s name and phone number are displayed. Caller information for the last 50 callers is logged in the caller list from the most recent call to the oldest. L If the unit cannot receive caller information, the...