Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
4 When finished, press [GREETING REC] or [STOP]. • To change the greeting, start again from step 1. [STOP] [ERASE] MIC VOLUME [<], [>] [GREETING REC] [GREETING CHECK] • If “ ” is displayed, 6 beeps sound and “Your greeting was not recorded. Record your greeting again.” is announced, start again from step 1. To adjust the speaker volume, press VOLUME [<] or [>] during playback. • 9 levels (0–8) are available while using the Answering System. The level is displayed on the base unit. To review the greeting Press [GREETING CHECK]. To erase the greeting Press [GREETING CHECK], then press [ERASE] while the recorded message is being played. • The unit will answer calls with a pre-recorded greeting (p. 22). Preparation For assistance, please call: 1-800-211-PANA(7262) 21 Preparing the Answering System Pre-recorded greeting If you do not record a greeting (p. 20, 21), one of two greetings will be played when a call is received, depending on the caller’s recording time (see below). To review the pre-recorded greeting, press [GREETING CHECK]. • A pre-recorded greeting will be played as follows: n When the recording time is set to “1 minute”, “2 minutes” or “3 minutes”: “Hello, we are not available now. Please leave your name and phone number after the beep. We will return your call.” • If recording time runs out, the unit will automatically switch to the “Greeting only” mode (see below), and no new messages will be recorded. n When the recording time is set to “Greeting only”: “Hello, we are not available now. Please call again. Thank you for your call.” Flash Memory Message Backup (Message storage) Messages stored in memory will not be affected by power failures. All messages are saved until you erase them. Caller’s Recording Time Handset You can select “1 minute”, “2 minutes”, “3 minutes” or “Greeting only” for the caller’s recording time. The factory preset is “3 minutes”. 1 Press [MENU]. 2 Scroll to “Initial setting” by pressing [d] or [B], then press Select. Initial setting KBack dB Select L 3 Press Select at “Set answering”. Set answering KBack dB Select L 4 Scroll to “Recording time” by pressing [d] or [B], then press Select. Recording time KBack dB Select L 5 Select the recording time by pressing [d] or [B]. • You can also select the recording time by pressing [1], [2], [3] or [0] (Greeting only). Recording time:3min KBack dB Save L 6 Press Save, then press [OFF]. Preparing the Answering System If you select “Greeting only”, the unit will answer calls with the greeting message, and then hang up. The unit will not record any incoming messages. The base unit will display “ ” instead of the number of messages. Number of Rings Handset You can select the number of times the unit rings before the Answering System answers a call, from “2” to “7” or “Toll saver”*. The factory preset is “4”. 1 Press [MENU]. 2 Scroll to “Initial setting” by pressing [d] or [B], then press Select. 3 Press Select at “Set answering”. 4 Press Select at “Number of rings”. 5 Select the number of rings by pressing [d] or [B]. • You can also select the number of rings by pressing [0] (Toll saver*), or [2] to [7]. Initial settingBack Select KdBLSet answeringBack Select KdBLNumber of ringsBack Select KdBLNumber of rings:4 Back Save KdBL 6 Press Save, then press [OFF]. *Toll saver When you call the unit from a remote operation, the number of rings will tell you if there are any new messages. If the unit answers on the 2nd ring, there is at least one new message. If the unit answers on the 4th ring, there are no new messages. To save the toll charges for the call, hang up immediately when you hear the 3rd ring. The 3rd ring indicates that there are no new messages. Preparation For assistance, please call: 1-800-211-PANA(7262) 23 Preparing the Answering System Recording Mode Handset Two recording modes are available. The factory preset is “Standard recording (16min)”, which provides more recording time (16min) and standard sound quality. “Enhanced recording (8 min)” provides less recording time (8 min) but clearer sound quality. 1 Press [MENU]. 2 Scroll to “Initial setting” by pressing [d] or [B], then press Select. 3 Press Select at “Set answering”. Set answering KBack dB Select L 4 Scroll to “Recording mode” by pressing [d] or [B], then press Select. Recording mode KBack dB Select L 5 Select the recording mode by pressing [d] or [B]. • You can also select the recording mode by pressing [1] (Standard) or [2] (Enhanced). Standard recording(16min) KBack dB Save L 6 Press Save, then press [OFF]. Message Alert Handset You can select whether or not the Ringer/Message Alert indicator on the handset will flash slowly when new messages have been recorded (p. 58). The factory preset is OFF. 1 Press [MENU]. 2 Scroll to “Initial setting” by pressing [d] or [B], then press Select. 3 Scroll to “Message alert” by pressing [d] or [B], then press Select. Message alert KBack dB Select L 4 Select “On” or “Off” by pressing [d] or [B]. Message alert:Off KBackdB Save L...