Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Initial setting KBack dB Select L 3 Press Select to select the desired item. Back Select 4 If the item has a sub-menu, select the menu item (p. 13). Repeat steps 2 and 3 until the desired item is displayed. If the item has no sub-menu, go to step 5. 5 Select the desired setting by pressing [d] or [B], then press Save to save your setting. • A confirmation tone will be heard and the setting will be saved. Back Save 6 Press [OFF] to exit programming mode. • To go back to the previous menu, press Back, or press Select while “---(Go back)----” is displayed. If you press this key in the main menu, the unit will exit programming mode. • After programming is complete, the display will return to the main menu or the sub-menu depending on which menu the selected item is located. (See the menu table on page 13.) • You can exit programming mode at any time by pressing [OFF]. • If you do not press any buttons for 60 seconds, the handset will exit programming mode. • If the unit detects a problem, an error message will be displayed (p. 64) and/or error beeps will sound. Programmable Settings Function Menu Table Handset You can use the following functions to customize your unit. See the corresponding pages for function details. • After pressing [MENU], you can also program menu items directly by pressing ([0] to [9], [*] and [#]) instead of using the soft keys (p. 62–63). Preparation Main menu Caller IQInitial settingRinger settingMessage play (p. 51) Date and time (p. 14) Voice enhancer (p. 27) Talk Caller ID (p. 30) Sub-menu IRinger volume (p. 17) Ringer tone (p. 18) Incoming call. (p. 46) View Info.? (p. 73) Get new Info.? (p. 72) Turn CIQ off? (p. 70) Sub-menu II * “Activate CIQ?” is displayed if you have not subscribed to openLCR service. “Turn CIQ on?” is displayed when Caller IQ is turned off (p. 70). Number of rings (p. 23) Set dial mode Set flash time Recording time Remote code Recording mode Caller ID edit Auto talk Key tone Set tel line Message alert Set answering Ringer tone Incoming call. Change language Set base unit LCD contrast (p. 22) (p. 56) (p. 24) (p. 24) (p. 19) (p. 47) (p. 16) (p. 15) (p. 34) (p. 45) (p. 16) Set line mode (p. 19) (p. 46) Talk Caller ID (p. 31) (p. 15) For assistance, please call: 1-800-211-PANA(7262) 13 Programmable Settings Date and Time Handset We recommend you set the date and time so that the unit will announce the day and time each message was recorded when you play back messages. 1 Press [MENU]. 2 Scroll to “Date and time” by pressing [d] or [B], then press Select. 3 1 Enter 2 digits each for the month, day, and year. (Ex. To set May 15, 2004, enter “05 15 04”.) 2 Enter 4 digits for the time (hour and minute). (Ex. To set 9:30, enter “0930”.) • If you enter a wrong number, press [d] or [B] to move the cursor to the incorrect number. Enter the correct number. Date and time KBack dB Select L Date:| 12.31.2004 Time:12:00 AM KAM/PM SaveL Example Date:| 05.15.2004 Time:09:30 AM KAM/PM SaveL 4 Select “AM” or “PM” by pressing AM/PM. Date:| 05.15.2004 Time:09:30 AM KAM/PM SaveL 5 Press Save. • The date and time are set and “E” disappears from the base unit display. • If the handset beeps 3 times, the date and time were not set correctly. Start again from step 3. 6 Press [OFF]. • When entering the time in step 3, you cannot enter numbers greater than 12. Do not use military time. (To set 13:00 hours, enter “0100”, then select “PM” in step 4.) The date and time may be incorrect after a power failure. When “E” flashes on the base unit display, set the date and time again. To confirm the date and time, repeat steps 1 and 2 above. • The current date and time are displayed. When finished, press [OFF]. For Caller ID service users (p. 29) • When a call is received, Caller ID information adjust the date and time if the time is incorrect. • Caller ID information will automatically adjust the date and time for daylight saving time. • If the date and time has not previously been set, Caller ID information will not adjust the date and time. Programmable Settings Display Language Handset You can select either “English” or “Spanish” as the display language. The factory preset is “English”. 1 Press [MENU]. 2 Scroll to “Initial setting” by pressing [d] or [B], then press Select. 3 Scroll to “Change language” by pressing [d] or [B], then press Select. 4 To change from English to Spanish, press Espanol. To change from Spanish to English, press English. • The display changes to the selected language. • You can also select a language by pressing [d] or [B]. Preparation 5 When Spanish is selected, press Salvar, then press [OFF]. When English is selected, press Save, then press [OFF]. Initial settingBack Select KdBLChange languageKBack dBSelect LDisplay :EnglishEspanol SaveKL • If you select a language you cannot read, change the display language again using direct commands (p. 63). Dialing Mode Handset If you have touch tone service, set the dialing mode to “Tone”. For rotary or pulse service, set to “Puls...