Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
If previously adjusted, the time/day will be heard. Enter the current time (hour and minute) using a 4-digit number. (Ex. To set 9:30, enter “0930”.) •The entered number is displayed on the base unit. Press © to select “AM” or “PM”. Press (#) repeatedly to set the day. Press [PROGRAM). •The unit announces the time/day. The clock starts working. •In step 4, you cannot enter numbers greater than 12. Do not use military time. (To set 13:00 hours, enter “0100” and select “PM” by pressing (#).) If a power failure occurs, the adjusted time/day will be erased. Reprogram the current time/day. To check the time/day Press [PROGRAM] (PLAYBACK) + ©. •The current time/day is heard. When finished, press (PROGRAM). [..........................— —---'- : For Caller ID service users (p. 3d) I «The Caller ID information will re-set the clock after the first ring if the J adjusted time is incorrect. However, if the time has not previously been set, the Caller ID information will not adjust the clock. •The Caller ID information will automatically adjust the clock for daylight saving time. 26 Selecting the Caller’s Recording Time You can select “1 minute”, “3 minutes” or “greeting only” for the caller’s recording time. Your phone comes from the factory set to “3 minutes”. 1 Press [PROGRAM). •The TALK indicator flashes. oThe IN USE/CHARGE indicator lights. 2 Press [PLAYBACK]. •“P” is displayed on the base unit. 3 Press ©. •The current setting is displayed on the base unit. 1: 1 minute 2: 3 minutes (factory preset) 3: greeting only 4 Press (7), ® or (3) to select the recording time. ©The setting is displayed on the base unit. 5 Press [PROGRAMI •A beep sounds. If you select “greeting only”, the unit will answer a call with the greeting message, and then hang up. The unit will not record any incoming messages. Selecting the Number of Rings You can select the number of times the unit rings before the answering system answers a call, from “2” to “7” or “AUTO” (for Toll Saver*). Your phone comes from the factory set to “AUTO”. 1 Press [PROGRAM]. •The TALK indicator flashes. •The IN USE/CHARGE indicator lights. 2 Press [PLAYBACK). ®“P” is displayed on the base unit. 3 Press ©. •The current setting is displayed on the base unit. 4 Press @, or {2} to (7) to set the number of rings. 0: Selects “AUTO”. “A" is displayed. 2-7: The unit will answer after the selected number of rings. 5 Press [PROGRAM). •A beep sounds. *Toll Saver (When set to “AUTO”) When you call the unit from a touch tone telephone: If the unit answers on the 2nd ring, there is at least one new message. If the unit answers on the 4th ring, there are no new messages. Hang up when you hear the 3rd ring. This will save you the toll charge for the call. 27 Making Calls With the Handset To have a hands-free conversation, connect the headset to the handset (p. 69). o R°° R°o 9oo 000 & (TALK) and Indicator (LOUD/RINGER] (REDIAL/PAUSE] ■m 1 2 Press (TALK). Talk •The TALK indicator lights. dii] Dial a telephone number. Talk •The dialed number is displayed. 1112222 •After a few seconds, the display will show the (DBQ ] length of the call. To hanq up. press (TALK) or place the Talk handset on the base unit. •The indicator light goes out. oo-oo-oo (iiii • If “Out of range" is displayed and an alarm tone sounds in step 1, move closer to the base unit or place the handset on the base unit, and try again. •To switch a call from the handset to the speakerphone, see page 30 and 33. 28 To redial the last number dialed on the handset Press [TALK] [REDIAL/PAUSE], To select the handset receiver volume Press [LOUP/RINGER) while talking. oEach time you press the button, the volume level will change from MEDIUM (preset) to HIGH to LOW. •The display will return to the length of the call. If noise interferes with the conversation Press [CH] to select a clearer channel or move closer to the base unit. Lighted handset keypad The handset dialing buttons will light when you press a button or lift the handset off the base unit, and flash when a call is received. The lights will go out about 10 seconds after pressing a button, lifting the handset or answering a call. Backlit LCD display The lighted handset display will stay on for about 10 seconds after pressing a handset button. 29 Making Calls With the Base Unit (Digital Duplex Speakerphone) 1 4 Press (DIGITAL SP-PHONE). •The DIGITAL SP-PHONE indicator lights. Dial a telephone number. When the other party answers, talk into the MIC (microphone). To hang up, press (DIGITAL SP-PHONE). •The indicator light goes out. (REDIAL/PAUSE] [HOLD/RINGER] [DIGITAL SP-PHONE) and Indicator • VOLUME®. 0 MIC •To switch to the handset while using the speakerphone: —If the handset is off the base unit, press [TALK], —If on the base unit, just lift up. ©During a call using the handset, the call can be switched to the speakerphone by pressing (DIGITAL SP-PHONE) on the...