Войти:
Оценок - 3, средний балл: 4 ( )

Инструкция по эксплуатации Clarity, модель D704HS

Производитель: Clarity
Размер: 679.6 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


- place it away from electronic appliances such as televisions, microwave ovens, radios, personal computers, wireless devices or other cordless phones. - avoid facing radio frequency transmitters, such as external antennas of mobile phone cell stations. - avoid plugging it into the same circuit as other major household electrical appliances because of the potential for interference. Try moving the appliance or the base unit to another power outlet. If the reception for a base unit location is not satisfactory, move it to another location for better reception. Depending on the surrounding conditions as well as spatial and structural factors, the range may be reduced. The range indoors is normally less than outdoors. Connecting the charger base station 1) Locate the charger base; note that the power adapter is permanently connected to your charger base. 2) Plug the end of power supply into the wall socket, as shown. PACKAGING CONTENTS/LOCATION INSTALLING YOUR HANDSET 1) Slide out the battery compartment cover. 2) Place the two batteries as indicated. Follow the polarity. 3) Slide the battery compartment cover back. 4) Put the handset on the base and charge for 16 hours first time. A beep indicates that the handset is properly placed on the base or charger. Use only NiMH rechargeable batteries. NOTE: Please refer to the Battery Safety Instructions on page 6 for proper use and disposal of the batteries. Your telephone (sold separately) can support up to five cordless handsets. The additional handset(s) needs to register with the telephone base before use. You must register each additional handset separately. The handsets provided within your main unit (sold separately) are already registered as HANDSET 1 and so forth. Additional handsets are assigned numbers in the order they are registered (HANDSET 2 to HANDSET 5). When first purchased, all expansion handsets alternately display • Press FIND on base 4 sec and • Then press # on handset. The new handset should be charged without interruption for at least 30 minutes before registering to the telephone base. How to add (register) your handset to the main unit (sold separately) NOTE: You must be in close proximity of your main unit's base in order to register the handset; please move to where you can access the FIND button on your main base (sold separately). 1. In idle mode, press

, then to select Registration. 2. Press and screen will alternately show • Press FIND on base 4 sec and INSTALLING/CHARGING BATTERIES HOW TO REGISTER YOUR HANDSET • Then press # on handset 3. Press and hold FIND on the telephone base for about four seconds. 4. Press # (pound key) on the handset. The screen shows Registering...Please wait. When the handset is registered successfully, HANDSET registered and then HANDSET X appears on the screen, with X being the handset number (1-5). If the registration is not successful, the handset screen shows Registration failed. Please start again from step 1 above. Note: You cannot register a handset if any other system handset is in use. To register an expansion handset, follow from the step 3 as above. Deregister all handsets You can deregister handsets. You may need to deregister your handsets if: You have five registered handsets and need to replace a handset. -OR- You wish to change the designated handset number of your registered handsets. You must first deregister ALL the handsets, and then register each handset you wish to use again, one at a time. If the base of your main unit is represented by either of the drawings below, follow the directions below the drawings: 1. Press and hold FIND on the telephone base for about 24 seconds; release FIND. 2. Immediately press FIND again. 3. When complete, the handset screen alternately shows • Press FIND on base 4 sec and HOW TO REGISTER YOUR HANDSET HOW TO DEREGISTER YOUR HANDSET(S) • Then press # on handset. 4. To register the handset(s) to the telephone base again, follow the registration instructions in section Register a handset. NOTE: There are no visual or audible alerts to indicate the base is under deregistration mode. If the base of your main unit is represented by the drawing below, follow the directions below the drawing: 1. Press and hold FIND on the telephone base for about 10 seconds, until the SPEAKER light starts flashing; release FIND. 2. Immediately press FIND again; you will hear two quick beep tones. 3. When complete, the handset screen alternately shows • Press FIND on base 4 sec and • Then press # on handset. 4. To register the handset(s) to the telephone base again, follow the registration instructions in section Register a handset. Note: • If the deregistration process is not successful, you might need to reset the system and try again. To reset, unplug the power from the telephone base and plug it back in. • You cannot deregister the handset(s) if any system handset is in use. Note: • If your handset is registered to a base, you can re-regis...

Эта инструкция также подходит к моделям:
Радиотелефоны - D702HS (679.6 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории