Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
About the Calls Log This phone assigns each incoming call a number from 1 to 50 at the handset. The most recent call will have the lowest number. When the memory is full, the oldest call information is deleted to make room for new incoming call information. See CALLER ID OPERATION, beginning on page 42, for more details. If you answer a call before call information appears on the screen, it will not appear in the calls log. About Adding Handsets This product is compatible with the AT&T 5800 Expansion Handset. You may add up to five additional 5800 units (purchased separately) to this phone. Follow the instructions provided with the additional handset(s) for installation and registration. • • NOTE: Although you can register up to six handsets, only four can be used at one time. 2 5830_CIB_1ATT 2002.11.8 10:31 AM Page 3 INSTALLATION Table/Desktop Installation • • NOTE: Install this telephone away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. 1 2 Connect the telephone line cord. Connect the power cord. Standard electrical outlet Modular telephone jack Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111. 3 INST INSTINSTALLA ALLAALLATION TIONTION 5830_CIB_1ATT 2002.11.8 10:31 AM Page 4 3 Install the handset battery. Use only AT&T Battery 2401, SKU# 91077. INSTALLATIONINSTALLATION b) Align the contacts and place the battery pack in the battery compartment. a) Remove battery compartment cover by pressing on the raised spot and sliding downward. c) Replace cover by sliding it on its track up over battery case until it snaps firmly into place. 4 Charge the handset battery. • Place the handset in the base. • Charge the battery at least 12 hours. After the first charge, the battery will charge in eight hours. 5 Check for dial tone. • After the batteries are charged, lift the handset and press P; you should hear a dial tone. 4 5830_CIB_1ATT 2002.11.8 10:31 AM Page 5 figure a Wall Installation 1 Connect the power cord and telephone line cord to the underside of the corded base, as shown (figure a). 2 Position the mounting bracket as shown (figure b). 3 Feed the telephone line cord through the hole in the center of the mounting bracket (figure b), align the bracket with the base, and slide into the hole on the base as shown (figure c). 4 Lock the mounting bracket in place (figure d). figure b 5 Plug the telephone line cord into a modular wall jack, and mount the base on the wall (figure e). a) Align holes on base with mounting studs on wall jack. b) Place power cord as shown. c) Pull base down on mounting studs until it locks into place. 6 Plug the power cord into an figure c electrical outlet not controlled by a wall switch (figure e). Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111. 7 Follow Steps 3–5 in “Table/Desktop Installation.” figure d figure e 5 INST INSTINSTALLA ALLAALLATION TIONTION 5830_CIB_1ATT 2002.11.8 10:31 AM Page 6 INST INSTINSTALLA ALLAALLATION TIONTION Spare Battery/Power Failure Backup You can buy a spare handset battery (AT&T Battery 2401, SKU# 91077, sold separately) and keep it charged in the base at all times. In the event of a power failure, a fully charged battery in the spare battery compartment will allow you to make and receive calls from the cordless handset only for up to 21/2 hours. The spare battery will fully charge in 24 hours. 6 5830_CIB_1ATT 2002.11.8 10:31 AM Page 11 iiiii iiiiiiiiii Ringer Volume Adjust the volume of the handset ringer. Setting the volume so that no bars show on the graph turns the ringer off. 1 Press MENU , then until the screen highlights HANDSET SETTINGS. 2 Press OK OK . 3 Press when RINGER VOLUME is highlighted. The screen displays RINGER VOLUME OK 4 Press or to hear samples of ring volumes. 5 Press to save the displayed setting. OK • • NOTE: Ringer Volume and Vibrate settings are independent. Adjusting Ringer Volume does not affect Vibrate. 11 FEA FEAFEATURE SETUP – HANDSET TURE SETUP – HANDSETTURE SETUP – HANDSET 5830_CIB_1ATT 2002.11.8 10:31 AM Page 13 iiiii iiiiiiiiii Vibrate Control When this feature is on, the handset vibrates when you have an incoming call. The default setting is OFF. MENU 1 Press , then until the screen highlights HANDSET SETTINGS. 2 Press OK , then until the screen highlights VIBRATE CONTROL. 3 Press OK . The screen displays VIBRATE OFF OFF OK ON 4 Press OK OFF or ON . 5 Press to save the displayed setting. • • NOTE: Vibrate and Ringer Volume settings are independent. Adjusting Vibrate does not affect Ringer Volume. 13 FEA FEAFEATURE SETUP – HANDSET TURE SETUP – HANDSETTURE SETUP – HANDSET 5830_CIB_1ATT 2002.11.8 10:31 AM Page 14 FEATURE SETUP – HANDSETFEATURE SETUP – HANDSETiiiii iiiiiiiiii Low Batt Tone You can set the handset to sound a tone when battery power is low, or you can turn the tone off. Default setting is ON. MENU 1 Press , then until ...