Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
FleetSync enables a variety of paging functions on your transceiver, some of which depend on dealer programming. Your dealer can set up either FleetSync or FleetSync II on your transceiver. Transceivers set up with FleetSync can communicate with other transceivers that have been set up with FleetSync. Likewise, transceivers set up with FleetSync II can communicate with other transceivers set up with FleetSync II. However, transceivers set up with FleetSync cannot communicate with transceivers that have been set up with FleetSync II, and vice-versa. Note: This function is available only in analog operation. SELCALL (SELECTIVE CALLING) A Selcall is a voice call to a particular station or to a group of stations. ¦ Transmitting 1 Select your desired zone and channel. 2 Press the key programmed as Selcall or Selcall + Status to enter Selcall mode. 3 Press the / keys to select the ID of the station you want to call. • If Manual Dialing is enabled, you can enter the station ID by using the microphone keypad, or by using the / keys. When using the / keys, cycle through the digits to select a digit, then press the key to set the digit and move the cursor to the right. Repeat this process until the entire ID is entered. 4 Press the microphone PTT switch and begin your conversation. ¦ Receiving An alert tone will sound and the transceiver will automatically enter Selcall Mode. The calling station’s ID will appear when a Selcall is received. When the call station’s ID appears on the display, you can respond to the call by pressing the microphone PTT switch and speaking into the microphone. FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION 18 ¦ Identifi cation Codes An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number. Each transceiver must have its own Fleet and ID number. • Enter a Fleet number (100 ~ 349) to make a fleet call. • Enter an ID number (1000 ~ 4999) to make an individual call in your fleet. • Enter a Group ID (which is programmed in the FPU) to make a group call. • Enter a Fleet number followed by an ID number to make an individual call in your desired fleet (Inter-fleet call). • Select “ALL” Fleet and “ALL” ID to make a call to all units (Broadcast call). • Select “ALL” Fleet and enter an ID number to make a call to the selected ID in all fleets (Supervisor call). Note: . Broadcast and Supervisor calls are programmed functions that cannot be made with a keypad. . The ID range may be limited by programming. STATUS MESSAGE You can send and receive 2-digit Status messages which may be decided in your talk group. Messages can contain up to 16 alphanumeric characters. Status messages range from 10 to 99 (80 ~ 99 are reserved for special messages). A maximum of 15 received messages can be stored in the stack memory of your transceiver. These saved messages can be reviewed after reception. Depending on your dealer settings, when the stack memory is full, either the oldest message will be erased when a new message is received or the new message will not be stored in the stack memory. The icon lights when a message is stored in the stack memory. ¦ Transmitting 1 Select your desired zone and channel. 2 Press the key programmed as Status to enter Status mode or Selcall + Status to enter Selcall mode. • When using the Status key to enter Status mode, the target Fleet/ ID is fixed and cannot be selected. Skip to step 5 to continue. 3 In Selcall mode, press the / keys to select the ID of the station you want to call. • If Manual Dialing is enabled, you can enter the station ID by using the microphone keypad, or by using the / keys. When using the / keys, cycle through the digits to select a digit, then press the key to set the digit and move the cursor to the right. Repeat this process until the entire ID is entered. 4 Press the key enter Status mode. 5 Press the / keys to select the status ID you want to transmit. • If Manual Dialing is enabled, you can enter the station ID by using the microphone keypad, or by using the / keys. When using the / keys, cycle through the digits to select a digit, then press the key to set the digit and move the cursor to the right. Repeat this process until the entire ID is entered. 19 6 Press the microphone PTT switch or the key to initiate the Status call. • “<
Радиостанции - NX-900 (399.5 kb)