Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
2) Using the DTMF keypad Press the keypad keys to enter characters as shown in the table below: DTMF Key Character Cycle 1 1 2 A B C 2 3 D E F 3 4 G H I 4 5 J K L 5 6 M N O 6 7 P Q R S 7 8 T U V 8 9 W X Y Z 9 0 [space] 0 15 SCAN Scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a signal is present. To begin scanning, press the key programmed as Scan. • The icon appears on the display. • When a signal is detected on a channel, Scan pauses at that channel. The transceiver will remain on the busy channel until the signal is no longer present, at which time Scan resumes. To stop scanning, press the Scan key again. Note: To use Scan, there must be at least 2 channels in the scan sequence. TEMPORARY CHANNEL LOCKOUT During scan, you can temporarily remove specific channels from the scanning sequence by selecting them and pressing the key programmed as Scan Delete/Add. • The channel is no longer scanned. However, when scanning is ended and restarted, the channels are reset and deleted channels will again be in the scanning sequence. PRIORITY SCAN Note: To use Priority Scan, a Priority channel must be programmed. When using a single Priority channel, the transceiver will automatically change to the Priority channel when a call is received on that channel, even if a call is being received on a normal channel. When using dual Priority channels, Priority channel 1 is given precedence over Priority channel 2. So, if a call is received on Priority channel 1 while a call is already on Priority channel 2, the transceiver will change to Priority channel 1. 16 SCAN REVERT The Scan Revert channel is the channel selected when you press the PTT switch to transmit during scan. Your dealer can program one of the following types of Scan Revert channels: • Selected: The last channel selected before scan. • Selected + Talkback: Same as “Selected”, plus you can respond to calls on the channel at which scan is paused. • Priority 1/ Priority 2: The Priority channel (either Priority 1 or Priority 2) . • Priority 1 + Talkback/ Priority2 + Talkback: Same as “Priority 1/ Priority 2”, plus you can respond to calls on the channel at which scan is paused. • Last Called + Selected: The last channel on which you receive a call. SCAN DELETE/ADD You can add and remove zones and/or channels/group IDs to and from your scan list. 1 Select your desired zone and/or channel/group ID. 2 Press the key programmed as Zone Delete/Add (to add/remove zones) or Scan Delete/Add (to add/remove channels/group IDs). • You can also press and hold the key programmed as Scan Delete/Add to add/remove zones. PRIORITY-CHANNEL SELECT If the Priority channel has been set as Operator Selectable by your dealer, you can reprogram the Priority channels. 1 Select your desired zone and channel/group ID. 2 Press the key programmed as Priority-channel Select. 3 Press / to select “NORMAL”, “PRIORITY 1” ( ), “PRIORITY 2” ( ), or “PRIORITY 1&2” ( ). 4 Press to save the setting and exit. 18 • Select “ALL” Fleet and enter an ID number to make a call to the selected ID in all fleets (Supervisor call). Note: . Broadcast and Supervisor calls are programmed functions that cannot be made with a keypad. . The ID range may be limited by programming. STATUS MESSAGE You can send and receive 2-digit Status messages which may be decided in your talk group. Messages can contain up to 16 alphanumeric characters. Status messages range from 10 to 99 (80 ~ 99 are reserved for special messages). A maximum of 15 received messages (combined status messages and short messages) can be stored in the stack memory of your transceiver. ¦ Transmitting 1 Select your desired zone and channel. 2 Press the key programmed as Status to enter Status mode (proceed to step 5) or Selcall + Status to enter Selcall mode (proceed to step 3). 3 Press / to select the station you want to call. • If Manual Dialing is enabled, you can enter a station ID by using the DTMF keypad, or by using / . When using / , cycle through the digits to select a digit, then press to set the digit and move the cursor to the right. Repeat this process until the entire ID is entered. 4 Press to enter Status mode. 5 Press / to select the status you want to transmit. • If Manual Dialing is enabled, you can enter a status ID by using the DTMF keypad, or by using / (refer to step 3, above). 6 Press the PTT switch or Side 2 key to initiate the call. • “
Радиостанции - NX-411 (447.04 kb)