Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
BUTTONS AND CONTROLS M PTT 11 12 13 9 10 14 TX LO BATT PAGE VOLUME MIC OFF 4 5 6 7 3 2 1 8 1. Channel up and down buttons - Pressing advances/decreases 1 channel. Holding continuously advances/ decreases channels until button is released. 2. PAGE - Sends a tone to other GE Sedona Series Family Radios tuned to the same channel. To send a page, hold the PAGE button. 3. MIC - Microphone 4. Speaker 5. Channel display 6. OFF-VOLUME control -Turn clockwise to turn ON and to increase listening volume. Turn counter-clockwise to decrease volume and turn power OFF. 7. TX LED - This light indicates when the unit is transmitting. 8. LO BATT LED - This light indicates when the batteries are nearly drained. 9. Antenna 10. PTT (PUSH-TO-TALK) - Press to transmit, release to receive. 11. M (Monitor) - Press and hold the MONITOR button to deactivate the automatic squelch feature to temporarily listen to the current channel. Release MONITOR to return to standby. 12. Battery compartment 13. Belt clip 14. MIC/ EAR jack - Eventually this product will offer an optional speaker/microphone or headset. NOTE: A standard audio headset will not operate with this unit. IMPORTANT: To page ALL radios tuned to the same channel irrespective of brand, hold the PTT button and press PAGE simultaneously. The page tone will BATTERY INSTALLATION continue until the PAGE button is released. 1. Remove the battery compartment door by sliding it down from the unit. 2. Install 3 AA-size alkaline batteries (not included) into the battery compartment. Make sure to follow the + and symbols in the compartment. Installing the batteries Sedona Series 15393460 (Rev. 1 E/S) incorrectly can damage the unit. Printed in Philippines BELT CLIP INSTALLATION AND REMOVAL • To install the belt clip, line up the grooves on the clip with the grooves on the back of P.O. Box 1976, Indianapolis, IN 46206 the unit. Place your thumb at the bottom of the clip and push upward until it snaps into © 1998 Thomson Consumer Electronics, Inc. place. Trademark(s) ® Registered Marca(s) Registrada(s) • To remove the belt clip, release the snap with your finger or a tool while firmly pushing the top of the clip downward. USING YOUR FAMILY RADIO 1. Turn on power. 2. Set to desired channel. 3. Adjust volume to comfortable level. TO TRANSMIT Press the PUSH-TO-TALK (PTT) button. Speak slowly and clearly 2-3 inches from the microphone.To avoid cutting off the first part of your transmission, pause slightly after pressing the PTT button before you start talking. TO RECEIVE When finished talking, release the PUSHTO- TALK (PTT) button to listen to the transmission. NOTE: Remember if several family radios are in use, they must all be on the same channel to communicate. NOTE: If none of the buttons on the unit are touched after 5 seconds, the unit will enter “sleep mode” to conserve battery power and will appear to be off. The display will become active again after a short delay once the PTT button is pressed or a transmission is received. This is IMPORTANT BATTERY INFORMATION • Alkaline batteries are recommended for longer play. Carbon-zinc or nickel cadmium rechargeable batteries can substantially reduce play time. • If you’re not going to use your radio for a month or more, be sure to remove batteries because they can leak and damage the unit. • Dispose of batteries in the proper manner, according to federal, state, and local regulations. • Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all batteries are not replaced at the same time, if disposed of in fire, or if an attempt is made to charge a battery not intended to be recharged. • Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury. FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. In accordance with FCC requirements, changes or modifications not expressly approved by Thomson Consumer Electronics could void the user’s authority to operate this product. This device generates and uses radio frequency (RF) energy, and if not installed and used properly, this equipment may cause interference to radio and television reception. If this equipment does cause interference to radio or television reception (which you can determine by turning the equipment off and on), try to correct the interference by one or more of the following measures: • Reorient the receiving antenna (that is, the antenna for the radio or television that is “receiving” the interference). • Move the unit away from the equipment that is receiving interference. If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communicat...