Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
For clock radios with a fitted plug. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. IMPORTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET. Should the fuse in the 13 amp plug require changing a 3 amp BS1362 fuse must be fitted. Battery back-up facility (unit will work without a battery being fitted) Your alarm clock radio is equipped with a battery back-up facility. 1 Remove the battery compartment cover (located underneath the unit) by pushing in the clip and lifting off. 2 Insert a battery size 9 volts PP3/6LR61 (Ensure batteries are inserted correctly) 3 Replace the battery compartment cover. Should a power interruption occur the clock will continue to run, however, time keeping will not be accurate. The display will be extinguished to conserve battery life but the memory will retain details of the clock time and alarm settings. If the optional battery is not installed in case of the AC power failure the display will blink to indicate the power was interrupted. You will need to reset the clock and alarm. Battery back-up is designed to operate for a short period only. If the unit is not to be used for a prolonged period, remove the battery to avoid battery leakage. In the interests of environmental safety : dispose of batteries safely. 2 3 4 1 6 7 8 9 5 12 13 14 15 16 11 10 Location of controls 1 Function selector switch 9 Clock display 2 Volume control 10 Minute button 3 Band selector 11 Snooze button 4 Tuning control 12 Alarm indicator 5 FM wire aerial 13 PM indicator 6 Speaker 14 Time button 7 Alarm button 15 Sleep button 8 Hour button 16 Battery compartment (underneath unit) P.2 Switching on, and setting the clock time Before any alarm functions can be used on your alarm clock radio you must first set the clock to the correct time. 1 Place the unit on a flat surface. Plug the mains plug into the wall socket and switch on the wall socket. 2 The clock LED display will flash. 3 Press and hold the TIME button and simultaneously hold down the hour button or the minute button. The LED clock display will fast forward the minutes and hour segments. Release all buttons when the correct time is set. 4 The PM indicator will illuminate to indicate 12.00 midday has been reached. Radio operation FM wire aerial To obtain the maximum FM reception fully extend the wire FM aerial (which is located at the rear of the unit) and alter the direction of the wire for best results. The aerial for the MW waveband is located inside the unit. To obtain the maximum MW reception rotate the clock radio. 1 Slide the FUNCTION SELECTOR switch to the ‘ON’ position. 2 Adjust the VOLUME control to a suitable level. 3 Set the BAND SELECTOR switch to either MW or FM as desired. 4 Slowly adjust the TUNING control to select your desired station. 5 To switch off the radio, slide the FUNCTION SELECTOR switch to the ‘OFF’ position. P.3 P.4 Alarm operation 1 Press and hold the ALARM button and simultaneously press the HOUR or MINUTE button to set the display to the desired alarm time. Release the ALARM button to set the alarm time. 2 Set the FUNCTION SELECTOR switch to the ‘AUTO’ alarm position. The ALARM ON indicator will appear on the clock display. Wake up to the radio alarm 1 Switch the FUNCTION SELECTOR switch to the ‘ON’ position to tune to the desired station. 2 Set the BAND SELECTOR switch to select either FM or MW wavebands as desired. 3 Adjust the VOLUME control to a suitable level. 4 Slowly adjust the TUNING control to the desired station. 5 Slide the FUNCTION SELECTOR switch to the ‘AUTO’ position. The ALARM ON indicator will light. The radio station will wake you up at the set alarm time. The alarm will automatically turn off after 2 hours. Ensure the station you select will be transmitting at the preset alarm time. Wake up to the alarm buzzer In order to check that the correct alarm time has been set press the ALARM button. The display will indicate the alarm time set. 1 Slide the FUNCTION SELECTOR switch to the ‘AUTO’ position. The ALARM ON indicator will light. Rotate the VOLUME control clockwise until a click is heard. The buzzer alarm will wake you up at the set alarm time. The buzzer will automatically turn off after 2 hours. P.5 Maintenance Do not expose your clock radio to extremes of temperature. The product should be kept in a warm environment free from dust and damp. For external cleaning use only a soft, clean, damp cloth. Use of detergents may damage the finish. Technical specification AC Power supply : 230v 50Hz Battery back-up : 9V DC type 6LR61/PP3 (not included) Radio : FM 88Mhz - 108Mhz : MW 540Khz - 1600Khz Warning labels WARNING: to reduce the risk of electric shock, do not expose this appliance to rain or moisture. ATTENTION: To reduce the risk of electric shock, do not remove the cover. There are ...