Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Remove the Battery cover on the base of your CD clock radio by pressing the tab on the cover and lifting in the Insert 2 x LR6 (AA size) batteries into the spaces Observe the correct battery polarity as shown inside compartment. Replace the battery cover. 2. Remove Battery cover on base of your remote control by rotating the cover to the Open position. Insert 2 x LR03 (AAA size) batteries into the spaces in the compartment. Observe the correct battery polarity as shown inside the battery compartment. Replace the battery cover. Mains Operation 1. Place your radio on a flat surface. 2. Plug the mains plug into a wall socket and switch on the wall socket. Note: The unit remains connected to the mains even when it is switched off. The unit is only isolated from the mains if the mains plug is removed from the wall socket. 1 2 Remote Control If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Display backlight During automatic on. The display back any button is pressed. The display backlight can also dim, bright and off. 1. Press the Light button for dim backlight, press once again for backlight and once again for off. 1 Night light 1. Press the Night Light button to adjust level of night for dim light press once again for bright light and once off. 1 Automatic When your Clock a power failure (when will proceed as follows: • Your radio will show "FM wavebands and store stations • Automatically set the time and 1. Connect to mains (see page 6). Your waveband, storing stations of sufficient Note: To interrupt the automatic tuning, press Prog/Random button once. 2. Your radio is ready for use when the FM waveband searched. After having performed the automatic memory set up process, display will show a DEMO briefly introducing the RDS features. 3. The Clock Time (CT) indicator will flash in the display whilst time setting is carried out. Note: To interrupt the automatic time set, or stop the DEMO mode, press any button once. 4. If the first station detected by the automatic setup does not carry CT information your radio will automatically change to another station after 1-2 minutes. This process will repeat until the clock is set. 5. Press the BAND button to switch on your radio and press the up and down buttons to select a preset station. Adjust the volume using the VOLUME control. To switch off your radio press the StandBy button. Note:- Auto setup can take up to 5 minutes to complete and is dependent on the signal strength and number of stations in your area. Should Auto setup fail, setting the clock and pre-setting stations can be carried out manually as described in the following sections. 5 5 5 5 If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Setting the The clock time and an RDS radio station is transmitted once every strength the clock will set 1. Switch on the radio with the BAND button on the CD clock radio or the BAND button on the remote control. 2. Select an RDS station using the Tuning Up/Down buttons. 3. "CT" will flash in the LCD display indicating that for an RDS time signal. The "CT" indicator will time is set. Note:- If the clock does not set within three to four minutes, station may not be transmitting clock time (CT) information, try another radio station. The clock time and day of week are updated every time the radio switched on and whilst listening to an RDS station transmitting clock (CT) information. Auto setup can take up to 5 minutes to complete and is dependent on the signal strength and number of stations in your area. Should Auto setup fail, setting the clock and pre-setting stations can be carried out manually as described in the following sections. 1 2 Remote Control 1 Setting the manually 1. Ensure that the 2. Press and hold down the Time button until the hour digit flashes. 3. Press the Tuning Up/Down buttons to set the correct hour. 4. Press the Time button to confirm. The minute digit now 5. Press the Tuning Up/Down buttons to set the correct minutes. 6. Press the Time button to confirm. The day of week now flashes. 7. Press the Tuning Up/Down buttons to set the correct day. 8. Press the Time button to confirm/complete the time setting. Note: The clock uses a 12 hour display 2 4 6 7 8 5 2 1 3 4 6 3 If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Setting the The alarms can be CD clock radio has 2 different times. Setting the alarms to wake 1. Ensure that the radio is switched (press StandBy). 2. Press and hold down the Alarm 1 or Alarm 2 button until the hour digit flashes. 3. Press the Tuning Up/Down buttons to set the correct hour. 4. Press the applicable Alarm button (1 or 2) to confirm. The minute digit now flashes. 5. Press the Tuning Up/Down buttons to set the correct minutes. 6. Press the applicable Alarm button (1 or 2) to confirm. 7. Press the Tuning Up/Down buttons to select BUZZ. 8. Press the applicable Alarm button (1 or 2) to conf...