Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Alarm selector switch 3. Function switch 4. Fast forward button 5. Slow reverse button 11. Alarm set button 12. Alarm off button 13. Snooze button 14. Sleep button (Right side) (Top) 1 6 8 9 10 14 13 12 11 6. Time set button 7. Headphone socket 8. Volume control 9. Waveband selector 10. Tuning control 7 Controls (Front) 15 1617 PM 1 2 88 540 92 600 96 800 100 1000 104 106 1300 108 1600 M H z kH z FM M W LW 150 170 210 240 260 kH z 19 18 15. PM indicator 18. Battery compartment (underside) 16. Alarm 2 indicator 19. Alarm 1 indicator 17. LED dial pointer If you need any further advice, please call our Technical Helpline on : 0181 758 0338 (Mon-Fri) Switching Before using your 1. Place the unit on a flat surface. and switch on. ON P M 1 2 88 54 0 92 60 0 96 80 0 100 1000 104 106 1300 108 1600 M H z kH z FM MW LW 150 170 21 0 24 0 26 0 kH z 2. The clock display will flash 12:00. PM 1 2 3. Press and hold down the Time Set button. Tim e S et Alarm 4. Whilst holding down theTime Set button press the fast forward ( Fast), or slow reverse ( Slow) buttons to set the time. Release the buttons when the correct time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. Fast Listening O ff Buzz Auto O n 1. Turn on the radio switch to the 'On' position. 150 170 210 240 260 kH z The LED dial pointer will light up indicating 540 600 800 1000 1300 1600 kH z on. 88 92 96 100 104 106 108 M Hz FM M W LW 2. Select the required waveband using selector switch. FMMW LW 3. Tune in to the desired station by rotating the Tuning control. The station frequency is indicated by the LED dial pointer. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for optimum reception. For MW and LW reception there is a built in ferrite aerial. Rotate your clock radio to the position giving best reception. Tuning 88 540 150 92 600 170 96 800 100 1000 104 106 1300 108 1600 210 240 260 M H z kH z kH z 4. Adjust the volume by rotating the Volume control. Volum e LW FM M W Off Buzz Auto On 5. The radio can be switched off by sliding the Function switch to the 'Off' position. Note: if the radio does not switch off, this may be caused by inavertent operation of the Sleep button. Press theAlarm/Off button to cancel. If you need any further advice, please call our Technical Helpline on : 0181 758 0338 (Mon-Fri) Setting alarm The alarms can alarm clock radio different times. 2 1 1+ 2 Setting alarm 1 1. Slide the Alarm function switch to the ' 1' position. 2. Press and hold down the Alarm set button. Tim e S et Alarm 3. Whilst holding down the Alarm Set button press the fast forward ( Fast), or slow reverse ( Slow) buttons to set the required alarm time. Release the buttons when the correct alarm time is reached. The uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. Fast S low 2 1 1+ 2 Setting alarm 2 1. Slide the Alarm function switch to the ' 2 ' position. 2. Press and hold down the Alarm set button. Tim e S et Alarm 3. Whilst holding Alarm Set button press the ( Fast) or slow reverse Slow) buttons to set Release the buttons uses a 12 hour display PM indicator. Ensure that the correct 12 hour cycle is selected. Fast S low Checking the Alarm Times 2 1 1+ 2 1. To check alarm 1 time, set the Alarm function switch to the ' 1 ' position. 2. Press the Alarm Set button to display the alarm 1 time. Tim e S et Alarm 3. To check alarm 2 time, set the Alarm function switch to the ' 2 ' 2 1 1+ 2 position. 4. Press the Alarm Set button to display the alarm 2 time. Note: The alarm times cannot be checked if the Alarm function switch is in the ' 1+ 2 ' position. Tim e S et Alarm If you need any further advice, please call our Technical Helpline on : 0181 758 0338 (Mon-Fri) Setting the 2 1 1+ 2 Off Buzz Auto On 1. Set the alarm time switch to the 'Buzz' position. Alarm selector switch to the ' 1' , ' 2 ' or ' 1+ 2 ' position. The corresponding Alarm indicators will light. The buzzer alarm will sound minutes. To turn off the alarm Alarm/Off button. To turn off the alarms permanently Function switch to the 'Off' position. To make a distinction between alarm 1 alarm 2 the alarm signals have a different sound pitch: Alarm 1 = lower pitch alarm signal Alarm 2 = higher pitch alarm signal PM 1 2 Setting the alarms to wake to radio 1. Set the alarm time as previously described. Set theFunction switch to the 'Auto' position. Set theAlarm selector switchto the ' 1', ' 2 ' or ' 1+ 2 ' position. The corresponding Alarm indicators will light. Ensure that the volume is set to the correct level and the desired station is tuned in. The radio alarm will operate every day at the preset time for 59 minutes. To turn off the radio alarm until the next day press the Alarm/ Off button. To turn off the alarms permanently set the Function switch to the 'Off' position. Note: If an alarm time has not been set and the Funct...