Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Connect the 12V power adaptor to the receiver. 3. Using the channel selector, select a desired channel and flip it to the “ON” position. *Only one channel can be in the ON position INSTALLING THE ALARM CLOCK CAMERA 1. Place the alarm clock camera in an appropriate location, connect it to the supplied adaptor and plug in the adaptor to your wall outlet. 2. Using the channel selector, select the same channel as chosen on the receiver and flip it to the “ON” position. *Only one channel can be in the ON position IN ORDER TO VIEW THE IMAGE ON YOUR TELEVISION OR VCR, IT MUST BE ON THE APPROPRIATE INPUT (A/V) CHANNEL. SETTING THE TIME AND ALARM ON THE CLOCK 1. Hold the [TIME] button down and press the [HOUR] and [MINUTE] button until you reach the correct time. 2. Hold the [ALARM] button down and press the [HOUR] and [MINUTE] button until you reach the desired alarm time. 3. To activate the alarm, set the [AUTO-ON-OFF] switch to AUTO. Sliding the switch to the ON position will turn the radio on. TROUBLESHOOTING If the Camera and/or Monitor You should... No Power 1. Check that the power cord(s) is properly connected. 2. Check that the monitor is turned ON. 3. Wrong AC/DC adapter used. Check that the adapter labeled OUTPUT: 10.2V ACx2 is connected to the clock camera, and adaptor labled OUTPUT: 12V DC is connected to the receiver. No picture. Distorted picture 1. Check the channel switch settings on the camera and receiver. Make sure the channels match on both units. 2. Signal interference from a microwave oven. Check if a micro-wave oven is in use or located in the path between the camera and monitor. If so, turn it off or move it out of the path. 3. Signal interference from other signal producing devices. (a) Identify and eliminate the source of the interference. (b) Relocate the camera and/or monitor closer to each other. (c) Change the channel setting on both camera and receiver. 4. Camera and receiver are too far apart. Relocate the camera and/or receiver. Product Specifications Receiver: Video Out ......................1 Vp-o 75 Ohm Audio Out ......................1 Vp-o 600 Ohm Power Supply..................10V DC, 600mA Operating Temp ............32oF - 122oF (0-50o C) Dimensions......................3.7” x 1.8” x 2.5” Weight ............................0.5lb (210 g) Clock Radio Camera: Image Sensor..................1/3” CMOS Image Sensor Resolution........................330 TV lines (H) Lens..................................6mm Power Supply..................10.2V DC x 2, 250 mA DC Backup Power ........DC 9V battery (not included) Frequency ......................AM 530-1600 KHz FM 88 - 108 MHz Operating Temp ............32oF - 122oF (0-50o C) Dimensions......................2.1” x 1.6” x 6.2” Weight ............................0.2lb (100 g) Antenna..........................FM with 1m wire antenna AM with built-in ferrite bar antenna Speaker ..........................1/4” 8 Ohm Dynamic Loudspeaker NOTES We take quality very seriously. This is why all of our products come with a one year warranty from the original purchase date against defects in workmanship and materials. PRODUCT WARRANTY If you have warranty or support issues please contact us using any of the following methods: SVAT Electronics USA SVAT Electronics Canada Phone: 866.946.7828 2315 Whirlpool St., Unit 333 4080 Montrose Road Fax: 888.771.1701 NIagara Falls, New York Niagara Falls, ON Email: support@svat.com USA 14305 Canada L2H 1J9 Website: Warranty Terms 1. SVAT products are guaranteed for a period of one year from the date of purchase against defects in workmanship and materials. This warranty is limited to the repair, replacement or refund of the purchase price at SVAT's option. 2. When service is required, the warranty is validated by the submission of a fully completed warranty card. 3. This warranty becomes void if the product shows evidence of having been misused, mishandled or tampered with contrary to the applicable instruction manual. 4. Routine cleaning, normal cosmetic and mechanical wear and tear are not covered under the terms of this warranty. 5. The warranty expressly provided for herein is the sole warranty provided in connection with the product itself and no other warranty, expressed or implied is provided. SVAT assumes no responsibilities for any other claims not specifically mentioned in this warranty. 6. This warranty does not cover the shipping cost, insurance or any other incidental charges. 7. You MUST call SVAT before sending any product back for repair. You will be given a Return Authorization number. When returning the product for warranty service, please pack it carefully in the original box with all supplied accessories, and enclose your original receipt or copy, and a brief explanation of the problem (include RA #). 8. This warranty is valid only in Canada and the U.S.A. 9. This warranty card cannot be re-issued. CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN TO REDUCE THE RIS...