Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
La date ou l’annee s’affiche pendant quelques secondes, puis l’affichage revient a l’heure qu’il est. Pour ameliorer la reception Si la reception est mediocre, modifiez l’emplacement et l’angle de l’antenne de l’horloge controlee par radio. Il est preferable de choisir un emplacement a proximite d’une fenetre. Laissez l’antenne filaire deployee. To improve reception When reception is poor, adjust the location and angle of the Radio-Controlled Clock antenna. A location near the window is preferred. Keep the wire antenna extended. • Do not place the unit where reception is weakened, such as: – near a TV, refrigerator, computer, etc. – on a steel table, steel shelf, or other steel objects. Location of transmitting source The Clock Auto Adjust clock data signal is transmitted from the following location: Mainflingen, Germany 50° 0.1’ N, 09° 00’ E Automatic updating of the clock data The Clock Auto Adjust system will automatically receive the clock data once every hour without any manual operation and corrects the clock, if needed, accordingly. “ ” will not flash but remain lit during such automatic operation. If the radio fails to receive the clock data signal for 12 hours, “ ” will disappear in the display. Note that, therefore, when “ ” is not displayed, the clock is not under control of the Clock Auto Adjust system. To initiate Clock Auto Adjust manually Press CLOCK AUTO ADJUST. “ ” will flash in the display. When the Auto Adjust process has been completed, the clock will be corrected, if needed, and “ ” will stop flashing and remain lit in the display. If the radio fails to receive the clock data signal for 12 minutes, the clock will remain unchanged and “ ” will disappear from the display. On Daylight Saving Time adjustment The Clock Auto Adjust system automatically switches the clock indication to Daylight Saving Time (summer time), and back, at the necessary time of the year. “ ” will be displayed when the clock is in Daylight Saving Time. Note • The actual adjustment to or from Daylight Saving Time by the Clock Auto Adjust system may be done up to 12 hours later than the exact moment of transition in the yearly calendar. Setting the Clock Manually If the clock does not adjust automatically due to poor reception of the clock data signal, you should adjust the clock manually. 1 Press CLOCK for a few seconds. The year will start to flash in the display. 2 Press TUNE/TIME SET + or – until the correct year appears in the display. 3 Press CLOCK once. 4 Repeat steps 2 and 3 to set the month, date, hour, and minute. After setting the minute, press CLOCK to start the counting of the seconds. • To set the current time rapidly, hold down the + or – button. • In step 4, when you press CLOCK after the minute setting to activate the clock, the seconds start counting from zero. Operating the Radio Manual Tuning 1 Press RADIO ON to turn on the radio. The display shows the band and frequency for a few seconds and then changes back to the current time. 2 Press BAND repeatedly to select the desired band. 3 Use TUNE/TIME SET + or – to tune in to the desired station. 4 Adjust volume using VOL. • To turn off the radio, press RADIO OFF. • To improve reception: FM: Extend the FM wire and Radio-Controlled Clock antenna fully to increase reception sensitivity. AM: Rotate the unit horizontally for optimum reception. A ferrite bar is built in to the unit. Do not operate the unit on a steel desk or metal surface, as this may lead to interference of reception. • To check the station being received, press the TUNE/TIME SET + or – button lightly. The display shows the band and frequency for a few seconds and then changes back to the current time. • If the radio alarm comes on while the radio is on, the unit switches to the station on preset button 1•WAKE UP STATION. To set the brightness of the backlight Set BRIGHTNESS for the display to HIGH or LOW according to your preference. Preset Tuning You can preset up to five stations for one-touch tuning; one for each of the preset buttons 1 to 5. Presetting a station Example: To preset AM 1260 kHz onto preset button 2. 1 Press RADIO ON to turn on the radio. 2 Tune in to the station you want to preset. (See “Manual Tuning”.) 3 Hold down the desired STATION• SELECT/PRESET button (in this case, 2) until you hear two short beeps. The display shows the frequency for a few seconds and then changes back to the current time. For the radio alarm, preset the station to be used as the alarm onto preset button 1•WAKE UP STATION. To change a preset station Tune in manually to the station you want to store and hold down the preset button until you hear two short beeps. The previously stored station will be replaced by the new one. Tuning in to a preset station 1 Press RADIO ON to turn on the radio. 2 Press the STATION•SELECT/PRESET button where the desired station is stored. 3 Adjust volume using VOL. After a few seconds, the display will return to the current time but the preset button number will remai...
Эта инструкция также подходит к моделям:Радиоприемники - ICF-C795RC (336.39 kb)