Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Cleaning Unplug the appliance from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the appliance. Clean the appliance only as recommended by Sony. Attachments Do not use attachments not recommended by Sony, as they may cause hazards. ANTENNAS Outdoor Antenna Grounding If an outdoor antenna or cable system is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits. WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Antenna Grounding According to the National Electrical Code SERVICE Damage Requiring Service Unplug the appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions: -When the power cord or plug is damage or frayed. -If liquid has been spilled or objects have fallen into the appliance. -If the appliance has been exposed to rain or water. -The appliance does not appear to operate normally or exhibits a marked change in performance. -This indicates a need for service. -If the appliance does not operate normally when following the operating instructions, adjust only those controls that are specified in the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to normal operation. -If the appliance has been subject to excessive shock by being dropped, or the cabinet has been damaged. Servicing Do not attempt to service the appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Replacement parts When replacement parts are required, be sure the service technician has used replacement parts specified by Sony that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards. Safety Check Upon completion of any service or repairs to the appliance, ask the service technician to perform routine safety checks (as specified by Sony) to determine that the appliance is in safe operating condition. Antenna Discharge Unit (NEC Section 810-20) Grounding Conductors (NEC Section 810-20) Antenna Lead-in Wire Ground Clamps NEC-NATIONAL ELECTRICAL CODE Electric Service Equipment Ground Clamps Power Service Grounding Electrode System (NEC Art 250 Part H) TUNE/TIME SET NAP BRIGHTNESS ALARM MODE ALARM SET CLOCK SET PRESET TUNING SLEEP STATION SELECT/ PRESET RADIO ON /BAND OFF ALARM RESET SNOOZE/SLEEP OFF 1 2 3 4 5 - + B A Setting the Clock 1 Plug in the unit. “AM 12:00” flashes on the display. 2 Press CLOCK SET for a few seconds until a beep sounds. The hour starts to flash on the display. 3 Press TUNE/TIME SET + or – until the correct hour appears. To set the current time rapidly, hold down TUNE/ TIME SET + or –. 4 Press CLOCK SET once. The minute starts flashing. 5 Repeat steps 3 and 4 to set the minute. Two short beeps sound, and the counting of the seconds starts. If you quit during the clock setting, after about 65 seconds the previous display will return. To set the current time from zero seconds, press CLOCK SET with the time signal in step 5. Setting the Brightness of the Backlight Press BRIGHTNESS to select high, middle or low for the display according to your preferences. Changing AM Channel Step The AM channel step differs depending on area. The channel step of this unit is factory-set to 9 kHz or 10 kHz to change the setting as shown below to be able to listen to the radio. Area Channel step North and South America 10 kHz Other countries/regions 9 kHz 1 Press OFF•ALARM RESET to turn off the power. 2 Press PRESET TUNING 1 and SLEEP at the same time for more than 5 seconds. Two short beeps will sound, and the AM channel step will be changed. If you proceed to step 2, the channel step will change again. Notes • When the AM channel step is changed, the preset stations for AM will be initialized. • When the AM channel step is changed, the FM channel step also will be changed. The PRESET TUNING 3 button has a tactile dot. VOLUME There is a tactile dot beside volume to show the direction to turn up the volume...