Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
The TUNER indicator goes off. NOTE: The Tuner remembers the last station that you were listening to and the selected volume level, and automatically returns to the same station and volume level when the system is switched ‘On’ again. 21 iC200_052906.p65 21 29/5/2006, 10:29 Presetting Stations In The Tuner Memory You can store a total of 20 stations, 10 FM and 10AM, in the tuner memory for easy recall at any time. 1.) Using either the Automatic or Manual Tuning method described above, tune to the first station you wish to store in the tuner memory. Example: FM 92.5 MHz 2.) When the desired frequency appears on the display, press the Memory button on the top panel once. “F 1” will begin flashing on the display indicating that you can now store your station in FM Preset Memory #1. 3.) Press the MEMORY button again. The “F 1” stops flashing. This indicates that FM 92.5 is now stored in FM Preset Memory #1. 4.) Tune to the next station that you wish to store. Press the Memory button once, then press the Preset button to select Preset Memory #2. “F 2” begins flashing in the display. 5.) Press the Memory button again to enter your desired station in Preset Memory #2. 6.) Repeat steps 4 and 5, using the Preset or buttons to select a different preset memory number each time until you have stored up to 10 FM stations in the memory. 22 iC200_052906.p65 22 29/5/2006, 10:29 7.) Press the Band button to switch to the AM band and repeat the above procedure to store up to 10 AM stations in the tuner memory. NOTES: • The FM memories are numbered “F 1” through “F 10”. The AM memories are numbered “A 1” through “A 10”. • After you press the Memory button the first time you must select a Preset Memory number and press the Memory button again within 10 seconds, while the memory number is flashing, or the station will not be memorized. Recalling Preset Stations Press the Band button to select the desired band. Press the Preset or buttons to scroll through the preset stations one by one. Changing Preset Stations 1.) Tune to the new station that you want to store. 2.) Press the Memory button and then press the Preset or buttons to select the Memory Number that you wish to change. 3.) When the desired Preset Memory Number is flashing, press the Memory button again. The new station is now stored and the previous station is deleted from the memory. 23 iC200_052906.p65 23 29/5/2006, 10:29 Antenna Information FM: The FM antenna is built in the AC power cord. You may have to extend and vary the direction of the AC power cord until you find the position that provides the best reception. AM: The AM bar antenna is inside the cabinet of the main unit. You may need to change the position of the main unit until you find the position that provides the best reception for your favorite AM stations. 24 iC200_052906.p65 24 29/5/2006, 10:29 25 Listening To Your “Dockable” iPod® / Charging The Battery IMPORTANT! To prevent distortion during iPod® playback you should go to the Main Menu of your iPod® , select the Settings Menu page, select the EQ Setting, and make sure that the EQ function is set to “Off”. (Main Menu > Settings Menu > EQ Setting > Select “Off”) This system provides an iPod® docking station on the top panel. You can connect any “dockable” iPod® , available as of January 2006, to the docking station and play your iPod® through the speakers of this system. When your “dockable” iPod® is in the docking area, the power to your device is being supplied by this system, not by the iPod® ’s internal battery. In addition when your iPod® is switched ‘Off’ while resting in the dock the internal iPod® battery is automatically recharged. NOTE: To prevent any possible interference between the iPod® and the Tuner in this system, the iPod® battery circuit is automatically switched ‘Off’ while you are listening to the radio. When the radio is ‘Off’ the battery charging circuit switches ‘On’ again automatically, regardless of whether the Power button of this system is ‘Off’ or ‘On’. Follow these steps to connect and listen to your iPod® . We recommend that you start with the power to this system switched ‘Off’: 1.) Open the docking area cover by gently pressing downward on the cover and sliding it backward. iC200_052906.p65 25 29/5/2006, 10:29 26 2.) Select the correct adapter for your particular iPod® model from among the 5 different adapters included. Each adapter is engraved with the name and/or size of an iPod® model. Place the selected adapter in the docking area so that the iPod® 30-pin connector passes through the opening in the adapter. Gently press downward on the adapter until it “clicks” and locks in place. 3.) Mount the iPod® Support Bracket on the docking station as shown. This bracket provides support and prevents your iPod® from moving too far backward when you operate the iPod® controls. CAUTION: You must use this support bracket with all iPod® models to prevent possible damage to the iPod® connector. IMPORTANT iPod® nano INSTRUCTIONS! I...
Эта инструкция также подходит к моделям:Радиоприемники - ITONE IC200 (678.25 kb)