Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Rev. A - Change Power station to charging stand pg. 3. 9-16-98 Rev. B - Change battery type from ni-cad to rechargeable pg. 3,4 9-16-98 Rev. C - Change Warranty and Customer Service telephone number 4-25-00 Model FR-214 CTCSS Privacy Code System active ON AIR Transmit mode active BUSY Signal being received BAT LOW Low battery voltage warning SCAN Channel Scan in progress CH Current channel LOCK Tranciever settings locked 1 128-5379C 2 of 12 Powering the transceiver: Your FR-214 radio transceiver kit includes three rechargeable AA batteries (RBP-214) and a charging station. You may operate your FR-214 using the rechargable batteries included or you may use alkaline batteries. Alkaline batteries will provide slightly better performance than the rechargable batteries. Installing the batteries: To install batteries into the radio, it is necessary to remove the belt clip. To do this you will need to rotate its thumbscrew counterclockwise. Next, release the battery compartment lock on the bottom of the transceiver by sliding it outward. The battery cover can now be removed by sliding it downward towards the bottom of the transceiver. Observe the polarity symbols on the bottom of the tray when inserting the batteries and replace the cover. Remember to lock the cover in place with the latch and replace the belt clip. 1 Remove belt clip 3 Insert batteries thumbscrew 2 128-5379C 3 of 12 2 Release battery cover lock Charging the RBP-214 batteries: Insert the charging adapter into a household electrical outlet and connect its power jack to the socket at the lower rear corner of the charging stand. Simply placing the radio into the charging stand will begin the charging process. The red LED in front serves as a charge indicator. The LED will flash rapidly when charging weak or dead batteries. As the batteries charge, the LED will flash at a slower rate. Fully charged batteries are indicated by a rate of one flash every 10 seconds or slower. Approximitally 6 hrs are required to fully charge the batteries. Remember to turn your FR-214 off before placing it into the charging stand. Important: The charging stand in your kit is intended for use with the RBP-214 batteries included in the kit. Do not attempt to recharge any other batteries with the charging stand. Operation: POW Button: (red) Press and hold this button for two seconds to turn the unit on. To turn the unit off, press and hold the button for another two-second period. MONI Button: A momentary press of this button will illuminate the display for viewing in low light conditions. The backlighting will remain on for five seconds. If any other buttons are pressed while the backlighting is on, the display will remain lit for another five seconds. This allows the light to remain on while the operator makes any necessary adjustments. To check the current volume setting, press the “MONI” button for two seconds, while the unit is on. If the volume is too high or too low, adjust it by using the up or down buttons as required. There are 15 possible volume levels. When a weak signal is being received by the transmitter (i.e. A voice becomes barely audible), press the “MONI” button for two seconds. This bypasses the squelch setting to temporarily allow very weak signals to be heard. 3 128-5379C 4 of 12 UP and DOWN Buttons: If these buttons are pressed before pressing the Lock/function button, a single press will display the current volume setting and subsequent presses will change the volume setting up or down. Important: If a speaker/microphone or earphone is used, check the volume setting before connecting it to the earphone jack. Be sure to set the volume low at first, and then raise it to a comfortable level. Lock/Function Button: The Lock button allows the user to eliminate the possibility of accidentally changing the transceiver’s selectable functions. Pressing and holding this button for two seconds will activate the lock function. “LOCK” will be displayed in the lower right of the display, indicating that the settings are locked in. While in the lock mode, it is still possible to adjust the volume, however other settings will be fixed. To unlock the transceiver simply, press and hold the lock button for 2 seconds. While the unit is unlocked, you may change any of the adjustable features by following the instructions that follow. PTT (Push To Talk) Button: Pressing and holding this button will allow you to speak to any transceiver that is set to the same channel and privacy code setting as yours. Hold the transceiver approximately 3 to 5 inches from your face as you speak. After you have finished speaking, release the PTT button to allow the reception of incoming signals. It is not possible to transmit and receive at the same time. “ON AIR” will show on the left side of the display and the red LED to the left of the display will illuminate while the PTT button is pressed. Low Battery Warning: “BATT LOW” will show in the upper right hand corner of the display as a warni...