Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
l) Press and release the “SET” key. m) The minutes will now flash. n) Press and release the “+” key to advance the minutes. By holding the “+” key, the minutes will advance in five minute increments. o) Press and release the “SET” key. Manual Date Setting p) The year will now flash. q) Press and release the “+” key to advance to the correct year. r) Press and release the “SET” key. s) The month will now flash. t) Press and release the “+” key to advance to the correct month. u) Press and release the “SET” key. v) The date will now flash. w) Press and release the “+” key to advance to the correct day. x) Press and release the “SET” key. y) The day of the week will now flash (Sun, Mon, etc.). z) Press and release the “+” key to advance to the correct day of the week. aa) Press and release the “SET” key. bb) “12” or “24” will now flash. cc) Press and release the “+” key to select either 12 –hour or 24-hour (military time). dd) Press and release the “SET” key to complete the programming. The programming is now complete. D. SETTING THE ALARMS La Crosse Technology’s travel alarm clock has two separate alarms that can be set. Each alarm has a distinctive sound and operates independently. a) Press and hold the “ALM1” (or “ALM2” key) key for two seconds to enter the setting mode. b) The alarm time will flash. c) Press and release the “HOUR” key to advance the hour of the alarm, and press and release the “MIN” key to advance the minutes of the alarm. Note: If no button is pressed within fifteen seconds, the alarm will set and activate, and the clock will revert to the normal operating screen. The picture below shows both alarms activated. Activating the Alarms To activate/deactivate the alarm, press and release the “ALM1” or “ALM2” key once, depending on which alarm needs to be activated. Activating the SNOOZE function When the alarm is sounding, pressing the top of the unit gently backwards will Text Box: “Alarm 2” activated Text Box: “Alarm 1” activated activate the snooze for the time that was selected in the programming mode. If the setting is “0”, the alarm will turn off for 24 hours. During the snooze period, the lower screen will show a countdown until the alarm will sound again. If the snooze is activated again during the original snooze period, the period will be reset. Once the period is finished, the alarm will sound again. Pressing any key other than the snooze will turn off the alarm for 24 hours. III. OPERATING SCREENS A. The exact time will always be displayed in the upper portion of the screen, and the US map will show when the time zone is set to the continental US (with the time zone selected showing in black). The lower portion of the screen has five different screens that can be selected. The default is “DAY, MONTH, DATE” as shown below. B. Press and release the “MODE” key to select which screen to show. It will change in order as follows: 1. DAY MONTH DATE 2. MONTH DATE YEAR 3. SECONDS 4. ALARM 1 TIME 5. ALARM 2 TIME C. While in non-alarm mode, pressing the “SNOOZE” bar will show the “ALARM1” and “ALARM2” briefly in the lower section. IV. TRAVELING A. When traveling, it will only be necessary to change to the appropriate time zone. Please note that the clock will only search for a signal when it is set between “GMT-4 and GMT-10.The alarm clock will set to any time zone from “GMT” to “GMT-12”. Outside this range, it will only be necessary to set the hour to the correct hour, leaving the time zone set to your local time zone. For example, if you are traveling to Hong Kong, you will need to manually set the hour to the local time. When the clock is back in the US, it will search for a signal and set to the proper time according to the time zone selected. TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, Problem: The time and date will not set initially. Solution: It usually takes overnight before the clock can receive the signal due to the interference the sun has on the WWVB signal. Wait overnight for the signal. Solution: Computer monitors and televisions can cause interference with the signal reception. Please keep the clock at least six feet from electrical sources. Solution: In some areas of the US, in particular on the East and West coasts, the signal is sometimes weak. It may take up to 72 hours before a good signal is received. The reception can be helped by placing the clock in a window facing Colorado, with the back towards Colorado. Solution: Be sure the time zone is set to a US time zone. MAINTENANCE AND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the unit. • Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the displays and casings. • Do not submerge in water. • Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer. • Opening the casings ...