Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Changes from 1 to 8 as selected by the user. Displays the current Battery charge level. LCD Screen Displays the current channel selection and other radio symbols. MENU Button Press to program the PMR settings. - (Power) button Press and hold to turn the PMR unit ON or OFF. Speaker Displayed when the Key Lock feature is activated. Displays the current Speaker volume level. Blinks when the Scan feature is turned ON. Antenna CALL button - Press to send a ringing tone to other PMR units. PTT (PUSH to TALK) button - Press and hold to transmit. Mic (Microphone) (UP)/ (DOWN) buttons - Press to change channels, volume, and to select settings during programming. Displayed when transmitting a signal. Displayed when receiving a signal. 2. Installation 2.1 Removing the Belt Clip a. Pull the Belt Clip Latch away from the PMR. b. While pulling the Belt 2.2 Loosen the screw counter clock wise direction using a coin or belt clip open the battery compartment as shown in Figure 2 Clip Latch, push up the Belt Clip as shown in Figure 1. 2.3 Installing the Belt Clip a. Slide the Belt Clip into the slot as shown in Figure 3. b. A “click” indicates the Belt Clip is locked into position. a. Slide down the Battery Compartment Cover. b. Insert 3 “AAA” size batteries (not included) by following the polarity marking inside the Battery Compartment as shown in Figure 4. c. Replace the Battery Compartment Cover.Tighten the battery door screw firmly to meet the IPX6 standard. See Figure 5. Figure 4 Figure 5 Notes: Use only same type and make of batteries on the PMR units. The PMR units have a built-in Power Saver (PS) for maximum battery life, but when not in use, turn the units OFF to conserve battery power. Remove the batteries if the units will not be used for a long period of time. Caution: Observe the proper battery polarity orientation when installing batteries. Incorrect positioning can damage both the batteries and the unit. Binatone Help Line - 0845 345 9677 4.7 Channel Scan Press and hold down the (UP) or (DOWN) button for 3 seconds. The channel number on the LCD Screen changes rapidly until an active signal is detected. When an active signal (one of the 8 channels) is detected, channel scan pauses on the active channel. Press the PTT button to communicate through the active signal channel, and the channel scan will be deactivated. (OR press the (UP) or (DOWN) button to continue the channel scanning.) Press the MENU button to stop the channel scanning operation. a. b. c. d. Channel scan performs searches for active signals in an endless loop from channels 1 to 8. This allows you to find other radios without having to change channel. To activate this feature; b. While the Channel icon is blinking, press the (UP) or (DOWN) button to select the desired channel. The channel changes from 1 to 8, or from 8 to 1. c. Press the MENU button to confirm your selection and return to the normal mode. Note: Refer to the "Channel Table" section of this Owner’s Manual for detailed frequency listing. 4.8 Key Lock To activate the Key Lock feature, press and hold the MENU button until the Key Lock icon ( ) appears on the LCD Screen. To deactivate the Key Lock feature, press and hold the MENU button again until the Key Lock icon ( ) disappears on the LCD Screen. a. b. The Key Lock feature allows the user to disable the (UP), (DOWN), and the MENU buttons so that the PMR settings cannot be changed accidentally. The PTT, CALL, and the (Power) buttons will remain functional even if the Key Lock feature is activated. 4.9 Calling (Paging) Tone With the PMR in normal mode, press and release the CALL button. The unit will transmit a 2-second page tone to the other unit/s set with the same channel within transmitting range . a. You can use the CALL button to send a tone to other users on the same channel. To activate this feature; 4.6.1 Monitor You can use the Monitor feature to check for weak signals on the current channel. a. To activate,press and hold the MENU and the (UP) button at the same time. b. If you hear constant noise and hissing, press the MENU butt o n to turn off the Monitor function. 3. Waterproof standard IPX6 though this unit is designed to meet IPX6 standard, it can be kept 1 meter under water for 1 minutes. 4.3 Receiving a Call The unit is continuously in Receive mode when the unit is turned ON and not transmitting. When a signal is received on the current channel, the receive signal icon “RX” will be displayed on the LCD Screen. 4. Operation 4.1 Turning the Unit ON/OFF To Turn ON; a. Press and hold the (Power) button. A special “beep" sound will be heard. The LCD Screen will be illuminated by an orange light for several seconds, and will display the current channel. To switch OFF; b. Press and hold the (Power) button. A special “beep" sound will be heard and the LCD Screen will turn blank. 4.5 Roger Beep The Roger Beep is a tone which is automatically transmitted whenever the PTT button is released. This alerts the receiving party that y...