Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
WAKE TO BUZZER 1. Reconfirm the wake up time and alarm mode settings for the alarm you are using, Alarm 1, Alarm 2, or both alarms. 2. Set the Alarm selector switch for one or both alarms to the Buzzer (Buzz) position. The appropriate Alarm 1 and/or Alarm 2 indicators will light up to confirm that the alarms are set. 3. At the selected wake up time the buzzer will sound. It will continue for one hour and then shut off automatically. 4. To stop the buzzer sooner, press either the appropriate Alarm 1 or Alarm 2 button. The buzzer will stop but the alarm remains set and will turn the buzzer on again at the same time on the following day (depending on the Alarm Mode setting). To stop the buzzer and turn on the radio immediately, press the Radio On/Off button instead of the Alarm 1 or Alarm 2 button. 5. If you do not want the alarm to turn the buzzer on the following day, set the appropriate Alarm selector to the ‘Off’ position. RADIO AND BUZZER OPERATION You may also set one alarm for wake to radio and the other for wake to buzzer. Just set the Alarm 1 and Alarm 2 selector switches to the desired positions. SNOOZE ALARM After the radio or buzzer alarm sounds in the morning you may press the Snooze Bar for a few more minutes sleep. The alarm will stop for approximately 9 minutes and then turn on again. You may repeat the Snooze operation up to seven times if desired, but after the seventh time the alarm will not turn on again. SLEEP TO MUSIC TIMER You can program the sleep timer to play the radio for up to 90 minutes and then shut off automatically. 1. Press the Sleep On button. The display will briefly show “10” and the radio will begin to play. After 10 minutes the radio will shut off automatically. Each time you press the Sleep button the sleep timer will start at 10 minutes. This is the sleep timer default setting. 9 2. To increase or decrease the amount of time that the radio will play before shutting off, hold the Sleep On button and press either the Up or Down button to change the display to the desired sleep time, up to a maximum of 90 minutes or at minimum of 2 minutes. Note: When you change the sleep timer from the 10 minute default setting to a different setting, the new setting becomes the default setting. Whenever you activate the sleep timer it will begin with your new default setting and count down to zero from that point. 3. To cancel the sleep timer before it counts down to “00” and shut the radio ‘Off’ immediately, press the Snooze Bar. IMPORTANT: Remember that the station and volume settings you choose for the Sleep To Music operation are the same settings you will hear if you set the alarm for wake to radio the following morning. DIMMER CONTROL The Dimmer control was set to the ‘High’ position at our factory. If you find the clock display is too bright in a darkened room, set the Dimmer control to the ‘Low’ position. CHANGING THE LITHIUM BATTERY Like all batteries, eventually the built in lithium battery will need to be replaced. A number of factors, such as, the length of time between the date the radio was manufactured and the date you plugged it in for the first time determine the amount of time before replacement. During this initial storage period, the lithium battery is supplying power to the SmartSet® computer memory. Once you plug the radio in, your household outlet supplies the power, and the battery is not being used. A fresh lithium battery can supply power to the SmartSet® computer for at least 3 years even if it is never connected to an AC power supply. If your radio was connected to your AC supply within a few months after it was manufactured, and you experience only the normal, nuisance type, short duration power interruptions, your battery may last for up to 5 years or even longer. When the battery power drops below a certain level, the Low Battery indicator will come on. When you see this indicator, you should change the battery as soon as it is convenient for you to do so. To change the battery proceed as follows: 10 1. Purchase a replacement 3V lithium battery wherever batteries are sold. The battery type is CR2430 or equivalent. 2. Remove the battery from its package so it is ready to install. 3. Important: Leave the radio power cord connected to your AC outlet. This will provide power to the SmartSet® computer memory while the original lithium battery is removed. 4. Turn the radio upside down and use a small screwdriver to remove the screw securing the battery holder to the cabinet. BE CAREFUL NOT TO LOSE THIS SMALL SCREW! 5. Turn the radio right side up and remove the battery holder. Then remove the original battery from the holder and insert the new battery into the holder the same way, with the positive (+) side facing up. Slide the holder with the new battery back into the opening in the cabinet. 6. Turn the radio upside down again and replace the screw that secures the battery holder in the cabinet. 7. Turn the radio right side up and confirm that the Low Battery ind...