Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
The iPod will continue charging in the dock. 9 10 Listening to a non-docking iPod® or other portable audio devices If you are using an iPod without a docking port, other MP3 player, or other portable audio device, you can play it through the iSoundSpa via the Aux Jack located on the back of the unit. 1. Plug one end of the Connection Cable (included) into the headphone or line-out jack on your MP3 device and the other end of the Connection Cable into the iSoundSpa Aux jack, located on the back of the unit (Fig. 5). 2. Press the POWER BUTTON on the unit to turn it on (Fig. 1). 3. Toggle through the AUDIO BUTTON on the unit until you reach the auxiliary mode (Fig. 1). The AUX ICON will appear in the lower right hand corner on the LCD display to indicate that the auxiliary mode has been selected (Fig. 2). 4. Turn on and play your MP3 device. 5. Use the VOLUME KNOB on the unit to adjust the system volume (Fig. 1). Note: You may need to adjust the volume on your MP3 device too. 6. To turn off the unit, press the POWER BUTTON. Note: You also need to turn off your MP3 device too. Listening to Nature Sounds 1. Press the POWER BUTTON on the unit to turn it on (Fig. 1). 2. Select the nature sound you wish to listen to and press the corresponding button (Fig. 1). 3. Turn the VOLUME KNOB on the unit to adjust the system volume (Fig. 1). 4. To turn off the nature sounds, press the POWER BUTTON to turn it off, or switch the audio mode by pressing the AUDIO BUTTON (Fig. 1). Note: When the unit is turned on, it will always default to the last mode used. Listening to the Radio Extend FM wire antenna fully for best FM reception (do not strip, alter or attach to other antennas). 1. Press the POWER BUTTON on the unit to turn it on (Fig. 1). 2. Toggle through the AUDIO BUTTON to play the radio (Fig. 1). The RADIO ICON will appear in the lower right hand corner on the LCD display to indicate that the radio is on (Fig. 2). 3. Slide the AM/FM SWITCH located on the back of the unit to select AM or FM band (Fig. 4). 4. Turn the SET +/- KNOB on the unit to tune in the desired station (Fig. 1). 5. Turn the VOLUME KNOB on the unit to adjust the system volume (Fig. 1). 6. To turn off the unit, press the POWER BUTTON. 11 Figure 5 iPod® Shuffle Connection Cable Aux SS-7000_6.qxd 8/17/06 11:31 AM Page 11 SS-7000_6.qxd 8/17/06 11:31 AM Page 13 Using Auto- Timer While listening to your iPod, the nature sounds, or the radio, you may set a timer so the unit will automatically turn off. 1. Toggle through the TIMER BUTTON until the corresponding blue LED light illuminates next to the time of your choice, 15, 30, 45, or 60 minutes (Fig. 1). 2. To cancel the timer, toggle through the TIMER BUTTON until the blue LED light is not illuminated, which indicates you are at the off position. Setting And Using The Alarms Setting Alarm1 or Alarm2 (Individually) 1. Slide the ALARM SWITCH located on the back of the unit to AL1or AL2 (Fig. 4). The AL1 or AL2 ICON will appear in the upper left hand corner on the LCD display to indicate which alarm is activated (Fig. 2). 2. Press the AL SET BUTTON twice; hour digits will begin flashing (Fig. 1). Turn the SET +/- KNOB until the desired hour is displayed (Fig. 1). Remember to set the correct AM or PM (an icon to the left of the time display is the PM INDICATOR; there is no AM indicator) (Fig. 2). 3. Press the AL SET BUTTON again; minute digits will begin flashing. Turn the SET +/- KNOB until the desired minute is displayed. 4. Press the AL SET BUTTON again to exit the alarm setting mode or after 5 seconds the display will stop flashing to indicate the alarm Note: You can press the AL SET BUTTON at any time to review the alarm setting. 5. Toggle through the AL MODE BUTTON until the corresponding blue LED light illuminates next to the wake mode of sound, radio, or beep (Fig. 1). Note: To wake to iPod, your iPod must be properly docked in the unit, or it will default to beep wake 12 Note: When using the sound mode, the unit will set to the last sound you listened to. If you wish to change it, first, turn the power on, then press the sound you wish to wake to. Lastly, turn the power off. 6. When the alarm is sounding, press the POWER BUTTON on the unit to turn the alarm OFF (Fig. 1). The alarm will come on again the next day at the same time. 7. To stop the alarm from coming on the next day, slide the ALARM SWITCH located on the back of the unit to the OFF position. The AL1 or AL2 ICON will disappear on the LCD display to indicate the alarm is disarmed. Note: If the alarm sounds for 30 minutes continuously it will automatically turn off. Setting Alarm1 and Alarm2 (Together) 1. Slide the ALARM SWITCH located on the back of the unit to BOTH (Fig. 4). The AL1 and AL2 ICON will appear on the LCD display to indicate both alarms are activated (Fig. 2). Note: You cannot change the alarm time when BOTH is selected. If you need to change the alarm time for either alarm, follow step under Setting Alarm 1 or Alarm 2 (Individual...
Эта инструкция также подходит к моделям:Радиоприемники - SoundSpa SS-7000 (674.25 kb)