Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
POWER SOURCE This radio is designed to operate on normal 120V 60Hz AC power only. Do not attempt to operate the radio on any other power source. You could cause damage to the radio that is not covered by your warranty. This radio should be connected to an AC outlet that is always ‘live’. Do not connect it to an outlet that is controlled by a wall switch. When the power to the radio is interrupted, the Sure Alarm battery back up system takes over to maintain the time and alarm settings. To maximize the life of the back up battery, keep the radio connected to a ‘live’AC outlet at all times. This radio uses a polarized AC plug which has one blade wider than the other. This plug will only fit into a polarized AC outlet. This is a safety feature. If the plug will not fit, you may have an older non-polarized AC outlet. Do not defeat the safety feature by trying to file the wider blade, or replacing the plug. Contact an electrician to replace your outdated outlet. 5 AC Plug AC Outlet CK5052_ib041503.p65 5 15/4/2003, 10:30 6 LOCATION OF CONTROLS AND INDICATORS 1.) Lighted Dial Pointer. 2.) DisplayDIMMER switch (HI/LO). 3.) ALARM 1 ‘On’Indicator. 4.) ALM 2 (Alarm) Selector Switch. (RADIO/BUZZER/OFF) 5.) AM indicator. 6.) ALM (Alarm) 1 Selector Switch. (RADIO/BUZZER/OFF) 7.) Time Display. 8.) VOL (Volume) Control. 9.) NAP Indicator. 10.) Band (AM/FM) Switch. 11.) ALARM 2 ‘On’Indicator. 12.) TUN. (Tuning) control. 13.) Back Up Battery Compartment. 14.) SNOOZE /SLEEP OFF) Button. 15.) RADIO ON/OFF Button. 16.) SLEEP Button. 17.) NAP Button. 18.) AC Power Cord. 19.) Speaker (Back Cabinet) 20.) TIME Setting Button. 21.) ALM 1 Setting/Reset Button. 22.) ALM 2 Setting/Reset Button. 23.) SET FWD (Forward) Button. 24.) SET REV (Reverse) Button. 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 19 20 21 23 24 13 22 CK5052_ib041503.p65 6 15/4/2003, 10:30 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS SETTING THE CLOCK When you connect the radio to your AC outlet for the first time, the display will begin flashing “12:00” PM (Noon). The flashing will stop when you set the time. 1.) Press and release the TIME button. The display will stop flashing and you can now proceed to set the clock. 2.) Depress the TIME button together with either the FWD or REV buttons for at least two seconds to move the display forward or backward to the correct time. The display will move rapidly forward or backward as long as the buttons are depressed. 3.) When the display approaches the correct time release the FWD or REV buttons and then repeatedly press the FWD or REV buttons to move display forward or backward, one minute at a time, until the correct time appears on the display. AM indicator Note: Observe the AM indicator to make sure you have set the clock to the correct hour, AM or PM. If the AM indicator is ‘On’ the time displayed is AM. If the AM indicator is ‘Off’ the time displayed is PM. 7 CK5052_ib041503.p65 7 15/4/2003, 10:30 SETTING THE WAKE UP TIMES This clock radio has two separate alarms that can be set and used independently. You may use the alarms to wake two people at different times, or you may use one alarm for weekdays and the other for weekend wake up times. The procedure for adjusting the wake up time is the same for both Alarm 1 and Alarm 2. 1.) Depress and hold either the ALM 1 or ALM 2 setting button. The display will change from the correct time to the Alarm 1 or Alarm 2 wake up time. 2.) While holding either the ALM 1 or ALM 2 setting button depress and hold either the FWD or REV buttons for at least two seconds to move the display forward or backward to the correct wake up time. The display will move rapidly forward or backward as long as the buttons are depressed. 3.) When the display approaches the correct wake up time release the FWD or REV buttons and then repeatedly press the FWD or REV buttons to move display forward or backward, one minute at a time, until the correct wake up time appears on the display. Note: Observe the AM indicator to make sure you have set the clock to the correct wake up hour, AM or PM. If the AM indicator is ‘On’ the time displayed is AM. If the AM indicator is ‘Off’ the time displayed is PM. CHECKING THE WAKE UP TIMES Whenever you want to check the wake up times, simply press either the ALM 1 or ALM 2 setting buttons. The display will change from correct time to wake up time. Release the ALM 1 or ALM 2 setting buttons to return to correct time. 8 CK5052_ib041503.p65 8 15/4/2003, 10:30 LISTENING TO THE RADIO Note: Set the clock before pressing the RADIO ON/OFF button to turn the radio ‘On’for the first time. 1.) Set the Band selector to the desired band, AM or FM. 2.) Set the VOL (Volume) control to a low setting. 3.) Press the RADIO ON/OFF button to turn the radio ‘On’. The dial pointer will light. 4.) Select your desired station with the TUN (Tuning) control. 5.) Adjust the Volume control to the desired setting. 6.) When you are finished listening, press the RADIO ON/OFF button to turn the radio ‘O...