Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
If the camera is not going to be used for a long period of time, please unplug the adapter and remove the batteries. * The camera can run off of batteries for up to 5 hours (IR OFF) 3. Rotate the rounded head of the camera to the desired angle for surveillance. 4-1-1. Camera channel setup 1. On the right side of the camera there is a channel selector switch marked CH1,CH2,CH3,CH4. If you have multiple cameras you would set each one on a different channel to avoid interference. 2. Press the channel button on the receiver to select the same channel as the camera. When the channels match the picture will be displayed on the screen. 4-1-3. Camera alarm setup 1. The camera provides Motion Detection and Sound Detection. For each mode you can select 3 sensitivity levels: Low, Middle, High. Motion Alarm Setup: This alarm will detect movement in front of the camera. If you slide the alarm setting switch to the Motion position and select the Sensitivity level, the system enters motion alarm mode. When movement is detected, the alarm sounds until you press the Eliminate Alarm Button. Within 1 minute the motion alarm starts the next alarm circle. Sound Alarm Setup: This alarm will detect sound. If you slide the alarm setting switch to the Sound position, and select the Sensitivity level, the system enters sound alarm mode. When sound is detected, the alarm sounds until you press the Eliminate Alarm Button. When the alarm sounds the screen will also display the video unless you have pressed the Sleep button. Within 1 minute the sound alarm starts the next alarm circle. Off Alarm Setup This option turns off the alarm function. If you slide the alarm setting switch to the Off position. The alarm function is disabled. Note: If the camera is being powered by dry batteries and you plug in the power adapter, the alarm function will not work until you slide the power off switch to the ON position. The alarm function will then be reactivated. 4-2. Setting up the Receiver 1. Connect the receiver to the adapter and then slide the power switch to the ON position. Note: --This receiver can also use dry batteries as a power source by loading 4 AA batteries into the battery compartment at the back of the camera with their polarities in the correct position. --The AC adapter will work instead of batteries after it is plugged in. If the camera is not going to be used for a long period of time, please unplug the adapter and remove the batteries. * The camera can run off of batteries for up to 5 hours. 2. Adjust the volume control to the desired level. 3. Set the channel of the receiver to the same channel as the camera by pressing the channel button continuously, the pictures will display on the screen when the channels match. Note: :::: For clearer pictures you can connect the receiver to a monitor/TV with the included AV cable (yellow for video and red for audio). 4-2-1. Operation of the Receiver 1. Volume adjustment Slide “Volume Switch” to adjust the volume of the receiver. 2. Channel selection Press “CH button” to select the desired channel. 3. Channel Looping Hold the “CH button” for three seconds to enter the loop mode. All the available channels will be displayed one by one (default interval is 5 seconds). 4. Sleep Mode Press the “Sleep Button” to shut down the LCD display and keep the voice function. Press the button again and recall the normal working mode. This can save energy. 5. Eliminate Alarm button Press “Eliminate Alarm” button to stop alarm voice. Within 1 minute, the alarm enters the next circle automatically. 5. Specifications Item Value GENERAL Transmission Frequency ISM 2,400~2,483 MHz Transmission Power 10mW/CE; 2mW/FCC Operating Frequency 2414MHz;2432MHz;2450MHz;2468MHz Unobstructed Effective Range 100m (328ft)(Min.) Modulation Mode FM Operating Temperature -10 ~ +50(Degree C) / +14~ +122(Degree F) Operating Humidity ;85%RH CAMERA Imaging Sensor Type CMOS Picture Total Pixels PAL:720.480 Pixels; NTSC: 720.576 Pixels Horizontal Resolution 380 TV Lines View Angle PAL:55°; NTSC:55° Minimum Illumination 0Lux BandWidth 18M Night Vision Range 5m Battery Working Time 5 hours (IR OFF) Motion Detection Distance 5m (16ft) Sound Control Sensitivity >63dB Consumption Current 120mA(IR OFF)(Max.) & 220mA(IR ON)(Max.) Power Supply DC +8V Dimensions(W.D.H) 86*48*135 mm (3.5*2*5.5 in) Weight 146 g (5.2 oz) RECEIVER LCD Screen Type 2.4 inches TFT-LCD Effective Pixels 480.240 Receiving Sensitivity ;-85dBm Video System NTSC/PAL Battery Working Time 5 hours Color Configuration R.G.B.delta Consumption Current 200mA(Max.) Power Supply DC +8V Dimensions(W.D.H) 86*54*143 mm (3.5*2.25*5.75 in) Weight 142 g (5 oz) * Actual transmission range may vary according to weather, Location, interference and building construction. * All the specifications are subject to minor change without prior notice. 6. FCC information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may no...