Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
• Position the baby unit at a higher level to get a good over view of the baby’s bed or playpen. Adjust the baby unit in a way that ensures the best visibility of your baby. B Warning: Do not position the baby unit with the microphone pointing too far down, as this may prevent the microphone from picking up sounds properly. For more information on the operating range, see section ‘Operating range’ below. 4.1.1 Operating range The operating range of the baby monitor is 150 meters (490 feet) in open air and line of sight. indoors the operating range is up to 30 meters (98 feet). Depending on the surroundings and other disturbing factors, this range may be smaller. For wet and moist materials, the range loss may be up to 100%. Dr y materials Material thickness Loss of range Wood, plaster, < 30cm 0-10% cardboard, glass (12in) (without metal, wires or lead) Brick, plywood < 30cm 5-35% (12in) Reinforced concrete < 30cm 30-100% (12in) Metal grilles or bars < 1cm (0.4in) 90-100% Metal or aluminum < 1cm (0.4in) 100% sheets 5 Features 5.1 Adjusting loudspeaker volume You can adjust the loudspeaker volume of the parent unit to the level you prefer. Press the volume up or down button to adjust the volume. 5.2 Adjusting display brightness You can adjust the display brightness of the parent unit to the level you prefer. 1 Press the brightness adjustment buttons on the parent unit to adjust the brightness of the video display. E N g L i S h •The display brightness bar appears on the display to show the selected display brightness. D Note: if the brightness is set to a high level, the parent unit consumes more power. •The volume bar appears on the display to show the selected volume. D Note: if the volume is set to a high level, the parent unit consumes more power. 9 5.3 Sound level lights The parent unit continuously monitors the sound level in your baby’s room and the sound level lights let you know if there is any activity. if your baby cries, the blue sound level lights light up on the parent unit. • As long as no sound is detected, the sound level lights are out. • When the baby unit picks up a sound, one or more sound level lights on the parent unit go on. The number of lights that go on depends on the loudness of the sound picked up by the baby unit.The sound level lights also go on when the parent unit is set to a low volume or when the voice activation mode is activated (see section ‘Voice activation’ below). 5.4 Voice activation The parent unit continuously monitors the sound level in your baby.s room. When the voice activation mode is activated, the video display only turns on when the baby unit picks up a sound. As long as no sound is detected, the video display is off to save power. To activate the voice activation mode, press the voice activation button on the parent unit. • The voice activation light on the parent unit goes on and the voice activation image appears on the video display. • When the baby unit detects a sound, the video display on the parent unit automatically goes on to show the baby. When no new sound is detected for 20 seconds, the video display goes out again. 2 To deactivate the voice activation mode, press the voice activation button on the parent unit again.The voice activation light goes out and the voice activation off image appears on the display. 5.5 Nightlight 1 Press the nightlight button on the base of the baby unit to turn on the nightlight. • The nightlight on the base of the baby 2 To select another lullaby, press the lullaby unit goes on. button. Continue pressing the ‘next lullaby’ button until you hear the lullaby you prefer. 2Press the nightlight button again to turn off the nightlight. 5.6 Lullaby function 1 Press the lullaby play/stop button on the parent unit to play a lullaby. • The lullaby star ts to play on the baby unit and is repeated continuously for approx. 15 minutes. On the video display you see which lullaby number is played and repeated.This number is shown in a blue square. D Note: You can also select the repeat symbol to play all lullabies repeatedly in a loop. 3 Press the lullaby play/stop button on the parent unit to play the lullaby selected. • The lullaby star ts to play on the baby unit and is repeated continuously. D Note: if you have selected the repeat mode, all three lullabies are played repeatedly in a loop. 4 To stop the lullaby, press the lullaby play/stop button again. E N g L i S h 11 5.7 Out-of-range alert When the parent unit is out of range of the baby unit, the parent unit beeps ever y 20 seconds and the out-of-range image appears on the video display. D Note: The out-of-range aler t is also active when the baby unit is turned off. 5.8 Night vision The camera has infrared lights that allow you to see your baby clearly, even in a dark room. When the camera detects low light levels, the infrared lights are turned on automatically. Place the baby unit 1 to 1.5 meters (3.5 to 5 feet) away from the baby to ensure a clear view. 5.9 Belt clip/stan...