Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Products whose reliability and operating quality bring reassurance. A Baby unit 1 night light 2 talk button 3 loudspeaker 4 DC power supply socket 5 power button 6 power light 7 channel selection switch 8 microphone 9 AC power adapter 10 Mode switch - MONITOR - INTERCOM 11 loudspeaker volume control 12 battery compartment cover B Parent unit 13 sound-level lights 14 microphone 15 talk button 16 system check light 17 charging base 18 AC power adapter 19 power light 20 volume control - on/off switch 21 channel selection switch 22 loudspeaker 23 charging light 24 battery compartment cover 25 DC power supply socket 26 system check alarm switch Important information Please read this guide carefully before using the baby monitor, and keep it for future reference. This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult super vision and should not be used as such. • Make sure the Baby unit and adapter cable are always out of reach of the baby, at least one metre away. • Never place the Baby unit inside the baby’s bed or playpen! • Never cover the baby monitor (with a towel, blanket, etc.). • Clean the baby monitor with a damp cloth. • Never use the baby monitor near water. • Radio equipment for wireless applications is not protected against disturbance from other radio services. Remove the battery - pack from the Parent unit if it is not used for long periods. ENGLISH Getting your baby monitor ready 1 Position the Baby unit at least one metre away from your baby. Never place the baby unit inside the baby’s bed or playpen. 2 Set channel selection switches to the same channel on both units. 3 Connect the power adapter to Baby unit socket. 4 Plug the power adapter into mains supply. 5 Move away from the Baby unit with the Parent unit. If units are positioned too close to each other then a high-pitched noise can be heard. 6 Connect the second power adapter to the Parent unit’s charging base socket. 7 Plug the second power adapter into a mains supply. 8 Place the Parent unit inside its charging base. > The red charging light lights. 9 Leave the Parent unit in charging base for at least 14 hours to fully charge the batteries. When batteries are fully charged, the Parent unit can be used cordlessly for up to 12 hours. 10 Place the Parent unit inside the charging base when power light on the Parent unit flashes red (an indication that batteries are low). You can leave the Parent unit in the charging base. A B C D CHANNEL TALK D DC 9V SYSTEM CHECK LEVEL CHARGE Using your baby monitor POWER OPEN - SENSITIVITY + 43 5 -VOLUME + 3 5 A B C D CHANNEL OFFON VOLUME Listening to your baby 1 Push the power button on the Baby unit to turn it on. > The power light lights (green). 2 Set the mode switch on the Baby unit to MONITOR 3 Switch the Parent unit on and adjust the volume to level you prefer using the VOLUME ON/OFF control. The digital SYSTEM CHECK light lights continuously (green) when the Parent unit and Baby unit are in touch with each other. 4 ENGLISH 5 Features explanation Avoiding interference If there is interference or if sound reception is poor, switch both units to another channel. Always make sure that the channel selection switches on both units are set to the same position. Monitoring baby silently Adjust the volume on the Parent unit to the lowest level using the VOLUME ON/OFF control (do not switch off). > the sound-level lights visually alert you to baby’s sounds. The more sound your baby makes, the more lights light. Checking that the units are in touch Check that the digital SYSTEM CHECK light on the Parent unit lights continuously (green) to confirm that the connection between both units is reliable. If the light flashes (red), move the Parent unit closer to the Baby unit. The light flashes if the units are out of range for more than 30 seconds or if there is interference. Switching on the system check alarm You can switch on the system check alarm on the Parent unit that beeps when the units are not in touch. The Parent unit is delivered with the system check alarm switched off. Open the Parent unit’s battery compartment cover. Set the switch inside compartment to the ON position ( ). Close battery compartment cover. The SYSTEM CHECK light can still flash even if the system check alarm is switched off. Switching on the night light Push the Baby unit night light to switch it on and off. > Switch off the night light when operating the Baby unit on batteries to conserve power. Range 250 m in open air The baby monitor has an operating range of up to 250 metres in ideal open-air conditions. This means that the units can see each other with no obstacles in between. Walls, ceilings, large objects and even glass affect the operating range. The more obstacles there are in between, the shorter the operating range. 1 2 3 ENGLISH Talking back to comfort your baby Push the power button on the Baby unit to turn it on. > The power light lights (green). Adjust the volume on the Baby un...