Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
– indicate the volume level of both Baby Unit and Parent Unit loudspeaker. ENGLISH 7 enience the Baby Unit can be mains or battery operated. C power adapter (7) to a mains socket and the cord to er supply socket (12) of the Baby Unit. y Unit is now ready for mains operated use. e the battery compartment cover (8). y Lock knob to the left (for this use a coin) and slide the AA size batteries noting the + and - configuration inside ies are not included; we recommend non-rechargeable Philips y compartment cover back in place. • Slide the cover upward until it clicks in position. • Turn the Battery Lock knob to the right (for this use a coin). > The Baby Unit is now ready for battery operated use. The Baby Unit operates for a minimum of 25 hours on fresh batteries Mains operated use y operated use y compartment. SC478_book.qxd 06-07-2004 09:46 Pagina 7 > When the battery check light (10) flashes red, the battery power is low. The Baby Unit should now still operate for 15 minutes. After that you should install new batteries. Tips: – Switch off the Baby night light to save battery power, when the Baby Unit is battery operated. – Remove empty batteries from the Baby Unit. Battery back-up As soon as the batteries are inserted battery back-up will be activated. In case of mains failure during mains operated use, the unit will automatically switch to battery operated use.As soon as the mains supply is back on the unit switches to mains operated use again. Getting the baby monitor ready + + + + ++++ +++ +++ + Parent Unit 1 Remove the battery compartment cover (20) by lifting the cover outward from the bottom. 2 Insert the two enclosed AA rechargeable batteries, noting the + and - configuration inside the battery compartment. 3 Put the battery compartment cover back in place. First slide the upperside of the cover into the recesses in the battery compartment.Then press the underside downwards until it clicks in position. 4 Connect the AC power adapter (19) to a mains socket. 5 Place the Parent Unit inside the charging base (17). > The red charging light (18) lights up. > The Parent Unit can be operated now, but you should leave it in the charging base until the batteries are fully charged (at least 16 hours). When the batteries are fully charged, the Parent Unit can be taken out of the charging base and used cordlessly for up to 16 hours. > When the battery check light (21) lights up red, the battery power is low. Place the Parent Unit inside the charging base to recharge the batteries. > If the rechargeable batteries begin to lose their effectiveness, replace them with two new rechargeable batteries. Note: Use rechargeable batteries only! Never operate the Parent Unit with other types of batteries! Disposal of batteries • Dispose of used batteries in an environmentally friendly manner. • Do not mix old and new batteries, or different types of batteries. • Remove Baby Unit batteries if the baby monitor is not to be used for long periods. 8 ENGLISH + + ++ ++ + + ++ ++ SC478_book.qxd 06-07-2004 09:46 Pagina 8 Connecting to the Parent Unit Slide the wider side of the clip into the small rectangular recess on the ent Unit. Make sure the pins on the underside are above wnwards until it clicks in position. om the Parent Unit ess the visible pin in the circular recess upwards and lift the clip Monitoring your baby Switching on the units y Unit at least one metre away from your baby. er place the Baby Unit inside the baby ’s bed or playpen. ess and hold the Abutton (5) on the Baby Unit to switch on the Baby ess and hold the Abutton (23) on the Parent Unit to switch on the Parent Unit. > All lights light up for 2 seconds and then turn off again. > The DECT SYSTEM LINK lights (3 and 15) of both units light up orange then start blinking (green).The units now search for connection. > The DECT SYSTEM LINK lights (3 and 15) of both units light continuously (green) when the units have established connection. You can now monitor your baby. • To switch off the units again press and hold the Abuttons (5 and 23). > The units will beep when they are switched off. Note:The Parent Unit beeps when it is (accidentally) switched off while monitoring. ENGLISH 9 SC478_book.qxd 06-07-2004 09:46 Pagina 9 SC478_book.qxd 06-07-2004 09:46 Pagina 9 Adjusting loudspeaker volume • Use the buttons (13) on the Parent Unit to increase/decrease the loudspeaker volume of the Parent Unit. • Use the buttons (11) on the Baby Unit to increase/decrease the loudspeaker volume of the Baby Unit. > The sound-level lights (25) on the Parent Unit give visual feedback on the volume settings on both units for approximately 2 seconds: 0 lights = Parent Unit volume switched off; 1 light = monitoring baby silently; 5 lights = maximum. Notes: – The volume of the Parent Unit can be switched off (0 lights). The volume of the Baby Unit cannot be switched off. – A high pitched noise may occur in case the units are too close to each other. To avoid this you should switch the Pare...