Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
Please read this guide carefully before using the monitor, and keep it for future reference. IMPORTANT! This Baby Monitor is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. Make sure the Baby unit and adapter cable are always out of reach of the baby, at least 1 metre away. Never place the Baby unit inside the baby’s bed or playpen! The antennas on the Parent and Baby units are fixed; do not try to extend them. Never cover the Baby unit (with a towel, blanket, etc.) GETTING THE UNITS READY FOR USE Baby unit Connect the AC power adapter (A-9) to an AC mains socket, and then connect the cord to the DC power supply socket (A-6) of the Baby unit. If you want to use batteries, remove the battery compartment cover (A-8) using a screwdriver. Insert four 1.5V, AA batteries (not included; we recommend non-chargeable Philips Alkaline batteries), noting the + and - configuration inside the battery compartment. Put the cover back in place and tighten screw. The Baby unit operates cordlessly for up to 30 hours on fresh batteries. The red POWER light (A-2) flashes when battery power is low. If this happens install new batteries. Note: To switch off the Baby unit completely push the POWER button (A-4) . Parent unit The Parent unit uses rechargeable batteries. These are already installed, but first they must be charged for at least 14 hours as follows before using the unit outside the charging base: • Connect the AC power adapter (B-11) to an AC mains socket, and then connect the cord to the DC power supply socket (B-10) of the charging base (B-6). • Place the Parent unit inside the charging base. The red charging light (B-13) lights. The Parent unit can be operated now but you should leave it in the charging base until the batteries are fully charged (at least 14 hours). When the batteries are fully charged, take the Parent unit out of the charging base and use cordlessly for up to 12 hours. When the red POWER light (B-1) on the Parent unit flashes, the battery power is low. Place the Parent unit inside the charging base to recharge the batteries. If the rechargeable batteries begin to lose their effectiveness, replace them with four new batteries (1.2V, AA NiMH) as follows: remove the battery compartment cover (B-7) using a screwdriver and insert the batteries noting the + and - configuration inside the battery compartment. Put the cover back in place and tighten screw. Only use 1.2V, AA NiMH rechargeable batteries! 3 HOW TO USE THE BABY MONITOR Monitoring baby’s sounds To use the units to listen to your baby: • Position the Baby unit at least 1 metre away from the baby so that the microphone (A-1) can pick up baby’s sounds. • Set the channel switch to the same position on both units. • Push the POWER switch on the baby unit (A-4) to switch it on. • Set the SENSITIVITY control (A-5) on the Baby unit to about mid-range (5). • The green TRANSMIT light (A-3) lights when a sound is picked up. • Move away from the Baby unit with the Parent unit. • Switch on the Parent unit using the Volume control/Off (B-4) and adjust the volume to the level you prefer. • If required, re-adjust the SENSITIVITY control (A-5) on the Baby unit to set the level at which the microphone will start to pick up sounds. When the SENSITIVITY control (A-5) is set to 9, the microphone picks up even the softest sounds. Experiment with different levels until you find the setting that suits you and your baby best. The green LINK light (B-2) lights continuously when the Parent unit and the Baby unit are in touch with each other. 4 ADDITIONAL FEATURES Avoiding interference Both units use anti-interference technology to reduce the chance of interference from other signals. If interference does occur or if sound reception is poor, try switching both units to the other channel to improve the sound quality. Note: Always make sure that the channel selection switches (A-7, B-8) on both units are set to the same position. Sound-level lights The Parent unit has sound-level lights (B-5), which visually alert you to baby’s sounds even when the volume control is turned down. The louder the sound received from the Baby unit, the more lights light. Checking that the units are in touch The green LINK light (B-2) of the Parent unit lights continuously to show that the Parent unit and the Baby unit are in touch with each other. This light flashes if the Baby unit is out of range for more than 30 seconds or if the signal is blocked. When the units are no longer in touch, try one of the following: • Move the Parent unit closer to the Baby unit. (The maximum operating distance is 250m in ideal conditions. Walls and floors can limit this distance.) • Switch both units to the other channel. • Check that both units are powered correctly (low batteries?). Switching on the audible warning If you wish, you can switch on a special feature that lets you hear an audible warning on the Parent unit when the units are n...
Эта инструкция также подходит к моделям:Радионяни - SBCSC365/86U (651.82 kb)