Производитель: Panasonic Размер: 1.11 mb Название файла: Язык инструкции:

Перейти к скачиванию

ENGLISH
IMPORTANT SAFETY INSTRUCTIONS FOR THE USER

Before using the vacuum cleaner, please observe these basic precautions.

WARNING: To reduce the risk of fire, electric shock, or injury
• This appliance is not intended for use by young children or infirm person without supervision; young children should be
supervised to ensure that they do not play with the appliance.
• Do not use the appliance if the mains lead or plug is damaged or faulty.
• This appliance is provided with a mains lead and if this becomes damaged, it must be repaired by an Authorized Service Centre
or a qualified person in order to avoid any hazard.
• Unplug from the socket when not in use and before cleaning the appliance or undertaking maintenance operations.
• Turn off the appliance before removing the plug. Do not pull on the mains lead, always pull on the plug body itself.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not use wet filters after wash, make sure they are completely dry to avoid damaging the cleaner.
• Do not vacuum flammable or combustible substances, neither use in areas where they may be present.
• Do not vacuum hot ash, embers or large and sharp objects.
• Do not vacuum water or other liquids.
• Keep the vacuum cleaner away from heat sources such as radiators, fires, direct sunlight, etc.
• This vacuum cleaner is fitted with a thermal cut-out device which automatically turns off the cleaner to prevent overheating of the
motor. When this happens, disconnect the cleaner from the mains socket and check the dust compartment and filters as they
may be full or clogged with fine dust. Check for any other obstructions in the hose or tube. After removing the obstruction, leave
the cleaner to cool down until the thermal cut-out resets after approximately 60 minutes.
A- IDENTIFICATION OF MAIN PARTS
C - HOW TO OPERATE YOUR CLEANER
A) Turbine nozzle (Only MC-CG467)
C-1 Pul out the mains lead and put the plug into the wall
B) Floor nozzle
socket.
C) Connection pipe
C-2 Gently press at the centre of the switch pedal to turn
D) Hose
ON the vacuum cleaner.
E) Suction regulator


Press the pedal again to turn it OFF.
F) Curved wand
C-3 Power control
G) Telescopic wand


To increase or decrease the power, turn the variable
(MC-CG467)
power control button.
(MC-CG465, MC-CG463)
H) Extension wand (MC-CG461, MC-CG461A)
C-4 Switching between carpet and flooring

Flooring: Press lever A
I ) Hose inlet

Carpet: Press lever B
J) Dust indicator

*Switching 3 positions for MC-CG467.
K) Dust cover

Flooring (PARQUET): Set position A
L) ON /OFF Switch pedal

Carpet (short): Set position B
M) Cord rewind pedal

Carpet (long or hard to push): Set position C
N) Crevice nozzle
C-5 The curved wand of the hose is attached with a manual
O) Dusting brush
suction regulator, which allows you to briefly reduce the
P) Parquet floor nozzle (Only MC-CG465)
suction level.
Q) Exhaust cover
C-6 After you finish vacuuming, remove the plug from
R) Plug
the wall socket and press the cord rewind pedal.


When rewinding the power cord, press the cord rewind
S) Variable power control button
pedal by holding the plug so that it does not become
damaged.
B - HOW TO ASSEMBLE YOUR CLEANER
C-7 Storage position


Insert the wand holder straight into the wand
B-1 Insert connection pipe into hose inlet until it locks. When
supporter.
removing hose assembly, pull out connection pipe with
C-8 Park system
pushing down two connection buttons.


For short breaks during vacuuming, slide the hook

NOTE: Do not bend, pull and step on the hose or put
attached to the nozzle pipe into the slot on the rear side
anything heavy on it.
of the cleaner.
B-2 Connect the two extension wands by inserting one into

NOTE: When you use park position, we suggest the
the other and twisting together. (Only MC-CG461, MC-
appliance is switched off.
CG461A)
B-3 Insert the hose unit into the upper end of the connected
extension wand (MC-CG461, MC-CG461A) or telescopic
wand (MC-CG465, MC-CG463), and the floor nozzle to
the other end

(MC-CG465, MC-CG463, MC-CG461, MC-CG461A ).
B-4 Insert the hose unit into the upper end of the telescopic
wand. Twist the telescopic wand so that the round hole
will fit into the tab on the hose unit. (When removing the
hose, push the tab down whilst pulling on the telescopic
wand)


Attach the Turbine Nozzle to the other end (Only MC-
CG467)( Removal as per reverse procedure)
B-5 You can adjust the length of telescopic wand by pushing
button. (MC-CG467, MC-CG465, MC-CG463)
18

---

...

Эта инструкция также подходит к моделям:
Пылесосы - MCCG467 (1.11 mb)

Скачать инструкцию

Чтобы скачать, введите 2 цифры: