Войти:
Оценок - 4, средний балл: 4 ( )

Инструкция по эксплуатации Bissell, модель LITTLE GREEN 1425

Производитель: Bissell
Размер: 270.66 kb
Название файла: 03bcf331-474c-4be9-b906-a60d835f63b6.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Heat indicator light After turning the Built-In Heater Switch on, the Heat Indicator Light will illuminate, indicating the heater has reached the correct temperature. Flex hose clip The clip guides the storage of the vacuum flex hose around the unit. TurboBrush clip Attaches to the unit for storage of the 2-in-1 crevice tool or TurboBrush. Tough stain brush The standard tool that attaches to the flex Hose. Quick Release cord wrap To remove the Power Cord, gently twist/rotate the Quick Release Cord Wrap clockwise Power Cord The Power Cord, with a three-prong plug, stores on the back of the Little Green by wrapping around the Quick-Release Cord Wrap. NOTE: Unwrap the Power Cord completely before operating the unit. WARNING: Do not use an extension cord with this product. The use of an extension cord may result in a severe electrical shock, particularly if the extension cord does not have an electrical rating higher than that of the product, OR if the extension cord does not have a three-prong grounding plug and if the extension cord is not plugged into a circuit box with a ground fault circuit interrupter. Safety precautions such as keeping all connections off the ground and dry will not eliminate the danger. WARNING: Do not use this product while on any type of ladder. Do not place the product in a place where it will be stepped on or kicked while in use. Do not place the product on an elevated surface where it may be pulled off the surface while in use. WARNING: Use only BISSELL Little Green formula in your cleaner. Use of cleaning formulas which contain lemon or pine oil may damage this appliance and void the warranty. Chemical spot cleaners or solvent-based soil removers also should not be used. These products may react with the plastic materials used in your cleaner, causing cracking or pitting. 800.237.7691 5 Assembly Assembly 3. 1. Assembling your Little Green PROheat is a simple process. The only thing you will need to assemble your cleaner is a Phillips head screwdriver. 1. Slide the back plate of the flex hose clip into the opening on the front of the unit. You will hear a “snap” when it is locked in place. 2. 2. Take the flex hose storage bracket and slide the lower plate into the opening on the back of unit. Make sure the screw holes line up. 3. Insert screw and tighten with a screwdriver. 4. Wrap the flex hose around unit and place hose grip into bracket. Turn bracket latch clockwise to lock in place. 4. 5. 5. Slide tool clip into slit on flex hose storage bracket place tool on clip 5. Operation Getting ready 1A. 1B. 1. To fill the clean/solution tank. A.Remove the tank by lifting it straight up and then away from the unit. B.Unscrew the black cap at the bottom of the clean/solution tank. C.Add BISSELL 2X Little Green Formula to the FORMULA fill line on the clean/solution tank. 1C. 1D. Fill the clean/Solution tank with hot (NOT boiling) tap water to the WATER fill line. Replace and tighten the black cap. D.Replace the clean/solution tank by lining up the vertical guides on the left side of the unit with the indentations on the clean/solution tank and gently sliding it down into position. 6 800.237.7691 Getting ready (continued) 2. Unwrap vacuum flex hose completely from onboard hose storage. 3. OperationGetting ready (continued) 2. Unwrap vacuum flex hose completely from onboard hose storage. 3. OperationAttach your selected cleaning tool to the spray trigger unit by pressing tool onto spray trigger firmly until the button lock snaps into hole. Make certain the tool is securely attached. 4. Twist the quick release cord wrap clockwise to unwrap the power cord completely from onboard cord storage and plug into 120 Volt, 60 Hz grounded outlet as described in Important safety Instructions, page 3. 5. Press power switch to ON position. Press the red heater switch to “ON”. Within 30 seconds, the heat indicator light will illuminate, indicating the heater has reached the proper temperature. 6. Begin by pressing the spray trigger for 5-10 seconds to allow the non-heated water to travel through the heater. 7. Press and hold spray trigger—spray will start in a few seconds. Raise the tool slightly to check for spray. Pre-treating Cleaning effectiveness will be enhanced if you pre-treat heavily stained or highly-soiled areas. Here’s how to do it: 1. Hold the cleaning tool just above the surface of the carpet or upholstery to be cleaned. Press the trigger to release a spray of cleaning solution directly onto the soiled area. 2. Wait 3-5 minutes before cleaning. 2. 3. 4. 5. 6. Power Switch Spray Trigger Heater Switch WARNING: Be sure to unplug the cord before attaching the TurboBrush (select models only). 800.237.7691 7 Operation Cleaning with your Little Green PROheat 1. Hold the tool approximately 1” above the soiled surface. Press the spray trigger to apply the cleaning solution to the soiled area. 2. Using the brush on the tool, gently scrub the area to be cl...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории