Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
*Do not boil or microwave water as it can destroy the bladder. 1. 2. 43. 7 800.237.7691 ug120-4073_1623_908.indd 7 10/14/08 12:59:37 PM Operation Fill the 2-in-1 water tank (continued) 5. Replace the top of the tank by matching the lid and tank edges. Handle must be in the forward position in order to replace lid. Rotate the handle to the carrying position to latch the lid. Note: Remember to secure the lid and test to make sure it is secure before picking up the tank. 6. Place tank into machine base, seating firmly in place. Rotate tank handle back into latched position. Carpet cleaning strokes 1. Plug the deep cleaner into a proper outlet. Turn the power ON by pressing the red power switch on the back of the unit with your foot. 2. With your foot, press the gray handle release lever located on the back of unit below water tank. 3. While pressing the spray trigger, make one slow forward wet pass and another back. Let the BISSELL advanced deep cleaning formula and DirtLifter PowerBrush do the work for you. Caution: Do not overwet. 4. Release the spray trigger and make one slow forward and backward pass over the same area to remove any residual dirty water and aid in drying. 5. Repeat cleaning passes until solution being appears clean. Continue passes without pressing the trigger until you can’t see any more water being suctioned up. 5. 6. Tip: Thorough vacuuming before deep cleaning will prevent early clogging of the lint trap. WARNING: To reduce the risk of fire and electric shock due to internal component damage, use only BISSELLcleaning fluids intended foruse with the deep cleaner. Non-BISSELL cleaning solutions may harm themachine and void the warranty. Power Switch Handle Release 8 800.237.7691 ug120-4073_1623_908.indd 8 10/14/08 12:59:37 PM 1. Operation1. OperationEmpty the 2-in-1 water tank/ clean removable nozzle Turn power switch OFF. Remove the 2-in-1 water 1. tank from the base using the tank carry handle. Carry the tank like a bucket to a utility sink or outside where you will dispose of the collection water. Remove the top of the tank by rotating the handle forward to unlatch lid and lifting lid off tank. 2. Empty collection water from bottom of tank. 3. After each use, remove and rinse the lint 3. screen located on the tank lid. 4. If nozzle needs to be cleaned: remove by grasping handle at the top and pulling forward.Clean removable nozzle by rinsing under running water. 5. When finished, replace nozzle by slightly raising front of machine to line up slots on the base with the hooks on nozzle. Attach at base first and then click nozzle into place. NOTE: If nozzle is not attached properly loss of suction will occur. 6. To continue carpet cleaning, refer back to pages 7 through 8, beginning with “Fill the 2-in-1 water tank” on page 7. If cleaning is complete, refer to the “Maintenance and care” section below. Ready Tools™ cleaning with attachments Your deep cleaner comes equipped with a hose and at least one attachment for cleaning stairs, upholstery, and more. Important! If using the machine to clean upholstery, check upholstery tags. 1. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your PowerSteamer. If the tag is coded with “X” or “S” (with a diagonal strike through), or says “Dry Clean Only,” do not proceed. Do not use on velvet or silk. If manufacturer’s tag is missing or not coded, check with your furniture dealer. 2. Check for colorfastness in an inconspicuous place. 3. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet. 4. Plan activities to give upholstery time to dry. 2. 5. Lint Screen 4. Manufacturer’s tag 800.237.7691 9 ug120-4073_1623_908.indd 9 10/14/08 12:59:39 PM Operation Ready Tools™ 5. Vacuum thoroughly to pick up loose debris and pet hair. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts. 6. To begin cleaning with attachments, follow the instructions on pages 7-8 for filling the 2-in-1 water tank and the formula tank. 7. Set the ReadyTools dial to the TOOLS setting. This will allow spray and suction from the hose. 8. Attach the cleaning tool to the end of the hose. 9. Clean by pressing the trigger to spray solution onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface. Release the trigger to suction dirty water. Continue to clean in the area, working in small sections, until dirt is removed. Caution: Do Not Overwet. 10. When finished cleaning, remove and rinse tool(s) in clean, running water. 11. It is recommended that you suction clean water from the tap to rinse out the hose. 12. Before wrapping hose onto tool rack, lift end of hose and stretch out to ensure all water is cleared from hose. 13. Wrap flex hose around tool rack. 14. Empty 2-in-1 water tank and rinse out, following instructions on page 9. 15. If the ReadyTools dial becomes difficult to turn, the diverter assembly...