Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
When carpet is dry, vacuum again to remove hair and fuzz the ProHeat ClearView may have loosened. 7. 8. 9. 1. 2. 3. 4. 5. 6. 10. WARNING: To reduce the risk of fire, electric shock or injuryunplug from outletbefore servicing. Tip: SmartMix Bottle may be stored with concentrate ready for your next cleaning job. Make sure dial is turned to the Water Rinse Setting when storing. ON OFF When filling bottle or storing unit, set dial to: Cap Rotor Filter Turn the machine off and unplug from the wall outlet. Step on the release pedal and recline the handle down onto floor (see illustration). Remove Tank-In-Tank and SmartMix tanks. Set them aside (see illustration). Remove Belt Access Door located near the Floor Cleaning/ Tools switch by inserting a flat head screwdriver into the slot nearest to the handle and gently prying the access door off (see illustration). Turn the machine onto its side so the belt access area is facing upward (see illustration). On the bottom of the machine, near the belt access area, is a red retainer plate that holds the black brush arm and brush in place. Using a Phillips head screwdriver remove the screw that holds the red retainer plate in place. Set red retainer plate and Phillips head screw aside (see illustration). Remove the black brush arm that holds the brush in place. Set the black brush arm aside (see illustration). Remove the “toothed” brush belt from the brush then from the red pump pulley. Set the “toothed” brush belt and brush aside. Locate and remove broken pump belt. 19 7. 8. 9. 7 8 9 To Remove Broken Pump Belt Pump Belt Replacement 1. 2. 3. 4. 5. 6. 2 3b 5 6 3a 4 20 With the unit still on its side, loop one end of the replacement pump belt around the red pump pulley and then the other end around the silver motor shaft (see illustration). Do not twist the replacement pump belt. Re-install the toothed brush belt first onto the red pump pulley and then onto the toothed end of the brush (see illustration). Re-install the brush into the base of unit. Place the black brush arm onto the brush and slide black brush arm into base of unit. The black brush arm and brush should slide easily into original position(see illustration). Re-install the red retainer plate and Phillips head screw (see illustration). Using your finger, gently spin the replacement pump belt on the silver motor shaft. If assembled correctly, the replacement pump belt should rotate freely around the silver motor shaft and drive pulley without obstruction. The brush should also rotate freely when the silver motor shaft is turned. Turn the machine right side up and replace the Tank-In-Tank, SmartMix Tank and Belt Access Door (see illustration).) Assembly is now complete. If you have any questions, or are having trouble installing your replacement pump belt, please call BISSELL Consumer Services at 1-800-237-7691. 6 7a 7b 5 5. 6. 7. 8. 1 2 3 4 To Install the Replacement Pump Belt 1. 2. 3. 4. 6 7a 7b 5 5. 6. 7. 8. 1 2 3 4 To Install the Replacement Pump Belt 1. 2. 3. 4. 21 Troubleshooting SmartTemp Ready Light does not illuminate. Possible Causes Remedies The SmartTemp switch is not Turn on the SmartTemp switch. turned ON. The machine Power Switch is not Both switches must be ON to turned ON. activate the SmartTemp Ready Light. Reduced spray or no spray Possible Causes Remedies Bladder may be empty. Refill tank with hot tap water. SmartMix bottle may be empty. Fill with BISSELL Deep Cleaning Formula for cleaning or water if rinsing. The filter may be clogged. Clean out Flow Indicator Filter, page 18. Tanks may not be seated properly. Turn power OFF; remove & reseat tanks. Pump may have lost prime. Turn power OFF; after 1 minute turn ON and depress trigger. The Pump Belt may be broken. Turn the machine OFF and unplug from the outlet. To check if a Pump Belt has broken, you will need a flat head screwdriver. Insert the blade end into the lower slot of the Belt Access door to release the lower snap. If necessary, insert the blade end into the upper slot to release the upper snap. Examine the belt for breakage. You should be able to see the Pump Belt looped around the motor shaft. If it is broken or missing, please refer to Replacement Parts on page 23 before calling Consumer Services. Complete installation instructions will accompany the replacement belt. DirtLifter PowerBrush does not turn. Possible Causes Remedies The Brush Belt or Pump Belt Turn the machine OFF and unplug from may be broken. the outlet. To check if a Pump Belt has broken, you will need a flat head screwdriver. Insert the blade end into the lower slot of the Belt Access door to release the lower snap. If necessary, insert the blade end into the upper slot to release the upper snap. Examine the belt for breakage. If broken refer to pages 19-20. WARNING: To reduce the risk of fire, electric shock or injury unplug from outlet before servicing. Lift Here Insert Screwdriver Blade Here Troubleshooting SmartTemp Ready Light does not illuminate. Possible Cau...
Эта инструкция также подходит к моделям:Пылесосы - 8905 (1.33 mb)