Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
. . . . . . . . . . .8-9 Cleaning bare floors . . . . .10-11 Putting it away . . . . . . . . . . . .11 Troubleshooting . . . . . . . . . . .12 Parts . . . . . . . . . . . . . . . . . . .13 Warranty . . . . . . . . . . . . . . . .14 Consumer services . . . . . . . . .14 1. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your POWERSTEAMER.T M If tag is coded with an “X” or “S” (with diagonal strike-through), or says “Dry Clean Only,” do not proceed. Do not use on velvet or silk. 2. If manufacturer’s tag is missing or not coded, check with your furniture dealer. 3. Check for colorfastness in an inconspicuous place. 4. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet. Always vacuum thoroughly before you deep clean. If possible, move larger furniture to an area you will not be cleaning. Tip: Deep cleaning carpeting and upholstery regularly can reduce dust and allergens in your home. How to deep clean carpet Pre-treating (optional) Pre-treat highly soiled carpet, such as hallways and other high-traffic areas. 1. Move POWERSTEAMERTM to an area to be cleaned. 2. Move 3-position Power Switch to the P R E - T R E AT ( I ) position to activate solution pump. 3. Press Release Pedal on Left side of Lower Chassis with foot. 4. Pull Trigger on Handle Assembly to spray cleaning solution as you move cleaner over soiled areas. 5. Slowly move cleaner back and forth over car- pet surface one time while depressing Trigger. Do not overwet. 6. Wait 5 - 10 minutes before full cleaning. How to deep clean carpet Pre-treating (optional) Pre-treat highly soiled carpet, such as hallways and other high-traffic areas. 1. Move POWERSTEAMERTM to an area to be cleaned. 2. Move 3-position Power Switch to the P R E - T R E AT ( I ) position to activate solution pump. 3. Press Release Pedal on Left side of Lower Chassis with foot. 4. Pull Trigger on Handle Assembly to spray cleaning solution as you move cleaner over soiled areas. 5. Slowly move cleaner back and forth over car- pet surface one time while depressing Trigger. Do not overwet. 6. Wait 5 - 10 minutes before full cleaning. Getting ready 1. Unfasten the Clean Water Tank Latch Assembly by lifting from the bottom with your fingers. 2. Remove Clean Water Tank Assembly by sliding it up the Handle Assembly until it comes free. 3. Take Clean Water Tank to sink area, remove Clean Water Tank Cap and fill Tank with hot (NOT boiling) tap water to fill line. Replace Cap securely. 4. Remove SmartMixTM Formula Tank Assembly from Clean Water Tank Assembly by grasping bottom with fingers and sliding it out. 5. Unscrew SmartMixTM Formula Tank Cap and Insert Assembly and add BISSELL Fiber Cleansing FormulaTM to fill line. Reclose Cap tightly. 6. Slide SmartMixTM Formula Tank Assembly back into position in Clean Water Tank Assembly. 7. Replace Clean Water Tank Assembly by sliding Tank down the front of the Handle Assembly until it fits snugly against top of Lower Chassis. Secure with Clean Water Tank Latch Assembly. 8. Select SmartCleanTM setting. ¦ WATER ONLY - Use for gentle cleaning of delicate fabrics, or for (optional) rinsing following cleaning. ¦ NORMAL - Water and Fiber Cleansing Formula are mixed to optimize normal cleaning. Use for everyday dirt and soil conditions. ¦ HIGH TRAFFIC - Water and Fiber Cleansing Formula are mixed to optimize heavy cleaning. Use for entryways, hallways, heavy soil and stains. This setting may require more frequent refilling on the SmartMixTM bottle. 9. Unwrap Power Cord from Cord Holder and plug into 120 Volt, 60 Hz grounded outlet as described in Important Safety Instructions, page 2. If cleaner starts when first plugged in, switch cleaner OFF (O) until ready for use. WARNING: U s e only BI SSEL L Fibe r Cleansing Formula™ i n your POWERSTEAMER.™ Use of cleaning formulas which contain lemon or pine oil may damage this appliance and void w a r r a n t y. Chemical spot cleaners or solvent- based soil removers should not be used. These products may react with the plastic materials used in your P O W E R S T E A M E R,™ c a u s i n g cracking or pitting. Deep cleaning 1. Move Power Switch to CLEAN ( II ) position to activate solution pump and vacuum motor. 2. Press Release Pedal on left side of Lower Chassis with foot. 3. Slowly move cleaner back and forth over carpet surface one time while depressing Trigger. Do not overwet. 4. Repeat motion over same area without depressing Trigger. 5. Repeat Steps 3 and 4 until no more dirt can be removed. 6. Continue to clean entire carpet, working in 3’ x 4’ sections. 7. Empty the Dirty Water Tank Assembly when dirty water reaches the full line. 8. If the machine loses suction and/or motor noise rises in pitch, turn Power Switch to OFF. Check the Dirty Water Tank Assembly and empty the tank if it is full [see WHEN YOU’RE DONE, page 7]. 9. If floor nozzle stops spraying, turn Power Switch to OFF and check water and cleaning solution levels. Refill if nee...
Эта инструкция также подходит к моделям:Пылесосы - 1695 (262.52 kb)