Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
Note: We recommend that you drain the water tank after every use. Caution: Upon initial use, the steam wil be mixed with water, hot enough to scald. Ensure that the floor brush is resting on the floor or the hose handgrip is directed away from user when steam switch is turned on. Never direct the nozzle or brush end of the unit toward yourself or anyone near you. OPERATING INSTRUCTIONS cont. 7 4. Fold the other side of the towel as shown in Fig. C. 3. Fold the towel as shown in Fig. B 6. Place the towel around the brush, and repeat folding the towel as shown in Fig. E. When folding the towel, leave some slack. Do notpull tightly around the brush, leave some looseness. Important User Information Please note that this steam cleaner has a “ flow through injection” type boiler and is nota pressurized system. It wil take approximately 45-90 seconds for the steam injector to heat up and the “ steam ready light” to go off. Once the steam ready light has gone off, push the steam switch on the handgrip to the “ On” position ( I) in order to start the steam flow. Steam power will steadily increase during the first four (4) minutes of use, after which time steam output will stabilize. Some steam will condensearound the floor brush when in use and will cause hard surfaces to become wet during the cleaning process, this is normal. Important: Please note that bristles may break through thin towels. We recommend that two (2) towels, laid one on top of the other be used. This will ensure that the brush bristles do not break through and that the towels will be sufficiently absorbent and retain as much dirt as possible. Very Important: When installing the towels to the floor brush, ensure that the towels do not cover the front and the back of the brush. (See fig. E)Attaching a Towel to the Floor Brush100% white terry cloth towel can be fitted on this brush, so as to absorb the dirt and protect delicate surfaces. Fig. CFig. B1. Prepare white terry cloth towel: size 8” x 17” as shown in Fig. A. 2. Place the brush on top of the towel. 5. Place the corner under the cloth holder as shown in Fig. D. Fig. DOpenOpenFig. EFig. A GETTING TO KNOW YOUR SHARK STEAM BLASTER 3 Technical Specifications Voltage: 120V~ 60Hz. Power: 1400 Watts Water Capacity: 3 1/4 Cups (.8 L.) Max. Steam Temp.: 240°F 1. Reservoir cover 2. On/ Off Switch 3. Steam Ready Light (Green) 4. Pivoting Wheels OPERATING INSTRUCTIONS cont. ON/OFF STEAM SWITCH 1. Before turning the steam switch to the “On” position, wait until the “ Steam Ready” light located on the unit has turned off. 2. Setting this switch to the “On” position wil start the flow of steam. CAUTION: Upon initial use, the steam will be mixed with water, hot enough to scald. Ensure that the floor brush is resting on the floor or the hose handgrip is directed away from user when steam switch is turned on. Never direct the nozzle or brush end of the unit toward yourself or anyone near you. CAUTION: The “On/Off Steam Switch” located on the handle must bein the “Off” position before attaching or disassembling accessories. Neverleave the “Steam Switch” in the “On” position when unit is not in use. Detail Cleaning Attachment This attachment is very useful for cleaning surfaces that are difficult to reach. It is ideal for radiators, door and window jambs, shutters and sanitary fixtures. The following parts can be applied to this attachment: Glass & Tile Squeegee This attachment is very useful for cleaning large windows, plastic material, ceramic, tiled surfaces, marble planes, etc. Apply steam abundantly, rub with the spongy side of squeegee and remove with the glass wiping rubber located at the front edge of squeegee. 6 Features • On/Off Switch • Thermostat & Safety Thermofuse • Steam Trigger on Handgrip • Steam Ready Light • 3 Pivoting Wheels 1234 Steam On/OffSwitch OPERATING INSTRUCTIONS PREPARATION FOR USE WARNING: ALWAYS unplug the appliance prior to any type of maintenance on the unit. As all the appliances are thoroughly tested before sale, there may be some residual water in the boiler. ASSEMBLY & OPERATION To connect the tube and the accessories (fig. 1), insert part (A) in part (B) turning this slightly to facilitate insertion. Make sure that key ( C) is securely fastened in the hole provided ( D). Open the reservoir cover (1) and pour in 3 1/4 cups (.8 liters) of tap water or distilled water if your tap water isparticularly hard. Never add cleaning fluids. Close the reservoir cover (1). Before plugging in the appliance, make sure that you have assembled the tubes and accessories correctly and the steam switch on handgrip is “Off” . Press the on/off switch (2) to “On”; the steam ready light (3) wil come on; when the light (3) switches off (after about 1 minute), you can start to use the appliance. To spray steam, simply press the steam switch button on the handle (6) (fig. 2). When there is no more steam, fill the tank again. To avoid damage, never use the steam gun without water. If the tank is full a...