Оценок - 1, средний балл: 5 ( )

Производитель: Philips Размер: 1.47 mb Название файла: Язык инструкции:

preparing for use hose To connect the hose, push it firmly into the appliance (‘click’) (Fig. 2). To disconnect the hose, push the buttons (1) and pull the hose out of the appliance (2) (Fig. 3). tube 1 1 To connect the tube parts to each other and to the handgrip of the hose, press the spring- loaded lock button.Then insert the part with the lock button into the part with the hole and fit the lock button into the hole (‘click’) (Fig. 4). To disconnect the tube from the handgrip, press the spring-loaded lock button and pull thehandgrip out of the tube. Note: Use the same method to connect and disconnect the accessories. Telescopic tube (specific types only) 1 Adjust the tube to the length you find most comfortable during vacuum cleaning (Fig. 5). Tri-Active nozzle (specific types only) The Tri-Active nozzle is a multi-purpose nozzle for carpets and hard floors. -The side brushes catch more dust and dir t at the sides of the nozzle and allow you to clean better along furniture and other obstacles (Fig. 6). -The opening at the front of the nozzle allows you to suck up larger par ticles (Fig. 7). To clean hard floors, push the rocker switch on top of the nozzle with your foot (Fig. 8). English The brush strip for cleaning hard floors comes out of the housing. At the same time, the , wheel is lifted to prevent scratching and to increase manoeuvrability. To clean carpets, push the rocker switch again (Fig. 9). The brush strip disappears into the nozzle housing and the wheel is lowered automatically. , Combination nozzle (specific types only) The combination nozzle can be used on either carpets or hard floors. To clean hard floors, push the rocker switch on top of the nozzle with your foot (Fig. 10). The brush strip for cleaning hard floors comes out of the nozzle housing. , To clean carpets, push the rocker switch again (Fig. 11). The brush strip disappears into the nozzle housing. , Crevice tool, small nozzle and small brush 1 Connect the crevice tool (1), the small nozzle (2) or the small brush (specific types only) (3) directly to the handgrip or to the tube (Fig. 12). Accessory clip (specific types only) 1 Snap the crevice tool and the small nozzle into the clip. Snap the accessory clip onto the tube (Fig. 13). Accessory holder (specific types only) 1 Snap the accessory holder onto the handgrip (Fig. 14). Snap two accessories into the accessory holder: -Crevice tool and small nozzle (Fig. 15). Note: Make sure the suction opening of the small nozzle points away from the holder. -Crevice tool and small brush (Fig. 16). Note: Make sure the suction opening of the small brush points towards the holder. using the appliance 1 Pull the cord out of the appliance and put the mains plug in the wall socket. Press the on/off button on top of the appliance with your foot to switch on the appliance(Fig. 17). During vacuum cleaning, you can adjust the suction power with the knob on top of theappliance (Fig. 18). -Use maximum suction power to vacuum ver y dir ty carpets and hard floors. -Use minimum suction power to vacuum cur tains, table carpets, etc. If you want to pause for a moment, insert the ridge on the nozzle into the parking slot topark the tube in a convenient position (Fig. 19) Active Fragrance Control (specific types only) The scent granules have been specially developed for use in your Philips vacuum cleaner. Only use the Philips s-fresh` scent granules in your vacuum cleaner. If the vacuum cleaner is equipped with Active Fragrance Control, keep it out of the reach of children, both during and after use. Store the vacuum cleaner in a locked cupboard if there aresmall children in the house. The scent granules are not edible. English In case of eye contact, flush immediately with plenty of water. Filling the cartridge 1 5 6 Place your thumb and index finger on the sides of the cartridge. Press on the disc (1) and lift the cartridge out of the holder (2) (Fig. 20). To remove the cap of the cartridge, apply pressure on the small pressing points (1) and then pull the cap upwards (2) (Fig. 21). Open the package at the small opening at the top. Fill the cartridge with the contents of one whole package of scent granules. Close the cartridge by putting the cap back onto it (‘click’). Re-insert the cartridge into the holder (‘click’). It only fits into the holder in one way (Fig. 22). Replace the granules when the car tridge no longer emits any fragrance. setting the fragrance level -You can set the fragrance level by turning the car tridge forwards (maximum emission) and backwards (minimum emission) (Fig. 23). -When you store the vacuum cleaner or do not want any fragrance to be emitted, close the car tridge by turning it backwards until the openings of the car tridge are no longer visible. storage 1 Switch off the appliance and remove the mains plug from the wall socket. Press the cord rewind button to rewind the mains cord (Fig. 24). Put the appliance in upright position.To attach the nozzle to the appliance, insert t...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: