Оценок - 4, средний балл: 3
(
)
)
|
Фрагмент инструкции
Do not remove the tag which provides test instructions from around the cord at the A.L.C.I. (A.L.C.I. may vary from illustration). DANGER: Improper installation of A.L.C.I. can result in electric shock. Do not modify or by-pass the A.L.C.I. Do not replace any electrical component in this product with anything other than an authorized ORECK replacement part. The risk of electric shock can result if used in the vicinity of improperly grounded stationary appliances (stove, refrigerator, washer, etc.). The ORECK STEEMER cleaner is designed for fast and easy set-up: STEP 1: Swing the wheels away from the nozzle into the operating position. Remove the two-tier tank from the cleaner by pinching the gray and red latch together, and then gently lowering the latch toward the nozzle. Do Not Force! (Figure 5) 5 A Pinch Latch 6 Lift Out and Lower B C STEP 2: Push the two-tier tank downward toward the nozzle and lift out (Figure 6). 7 Fill Line STEP 3: To fill the supply tank with clean water, open the gray tank cap. Fill the tank with lukewarm tap water to the fill line, as noted on the side of the tank (Figure 7). CAUTION: Do not overfill tank or use water that is too hot to touch. Do not put any type of shampoo/cleaner into the supply tank. Other carpet shampoo will leave residues in the cleaner that will over a short period of time clog the dispensing system and void your warranty. Use only STEEMER Full Release™ Professional Carpet Cleaner cartridges, which are specifically formulated to be residue-free. 8 A B C STEP 4: Close gray cap and place the tank back on the cleaner (Figure 8). Lift the gray latch to slide the tank upward into position until you hear a “click,” signaling that the tank is securely locked into place. Test Button Reset Switch Instructional Tag DO NOT REMOVE 6 To Set-Up Cleaner Operating Instructions Operating Instructions 9 10 Reset Switch Test Button STEP 5: Unscrew the cleaner cartridge cap from a STEEMER Full Release™ Carpet Cleaner cartridge. Insert the cleaner cartridge into the docking bay (Figure 9) on the side of the cleaner. The directions on the cleaner cartridge must be facing you. Rotate the white locking lever on the cartridge from left to right to lock and seal the cartridge in the cleaner. STEP 6: Plug in the power cord. Test and reset the A.L.C.I. Iocated near the plug. To test, press the test button to shut off power. To reset the A.L.C.I., simply push in the red reset button on the plug (Figure 10). To Prepare Carpet Always vacuum thoroughly before using the ORECK STEEMER carpet cleaner. It provides excellent carpet cleaning on carpeted surfaces that are free of surface debris. To achieve best results, high traffic areas and carpet stains should be pretreated prior to cleaning. We recommend STEEMER Full Release™ Professional Spot & Stain PreCleaner. CAUTION: Before cleaning a carpet for the first time, test a small area for color fastness. Pour a small amount of STEEMER Full Release™ Professional Carpet Cleaner on a clean white cloth and blot carpet. Examine this cloth for color removal; if color appears on the cloth, the carpeting is not colorfast and should not be cleaned with the ORECK STEEMER wet extraction process. This product is not recommended for use on carpets made from silk, velvet, wool and some cotton blends. TO CLEAN CARPET (Figures 11 and 12) WARNING: Do not push forward! Pull the cleaner towards you to clean. This cleaner has been specifically designed to place the nozzle deep into the carpet. (Figure 11). Push down gently on the handle to lift the nozzle out of the carpet, to move forward and reposition the cleaner (Figure 12). 11 12 IMPORTANT: Adjust the speed of the cleaning stroke to your carpet conditions. Heavily soiled or stained carpets will require slower strokes. Avoid oversaturating the carpet. 13 On/Off Switch 14 Cleaner Spray Button STEP 1: Place On/Off power switch in the “On” position. (Figure 13). STEP 2: To clean the carpet, press the gray button in the handle (Figure 14) and slowly pull the cleaner backwards (Figure 11). Pressing the button releases the cleaner and water mixture onto the carpet. As you pull the nozzle over the sprayed carpet, the nozzle extracts the solution from the carpet and stores the dirty water in the recovery tank. To move forward, slightly tilt the nozzle off the floor and roll the cleaner forward (Figure 12). Repeat Step 2 working in small overlapping rows for even cleaning until the entire room has been completed. 7 Operating Instructions To shorten the drying time, go back over the carpet pulling slowly backwards without depressing the gray button (Figure 14). Repeat this procedure until you do not see water being pulled from the carpet through the nozzle. CAUTION: Do not allow the lower recovery tank to overfill. Damage to the unit can result. Empty the recovery tank when full and whenever clean water is added to the upper supply tank. To empty the recovery tank, simply release the tank latch by squeezing the red and...
Эта инструкция также подходит к моделям:Пылесосы - XLS465 (586.65 kb)