Оценок - 1, средний балл: 4 ( )

Производитель: Nilfisk-Advance America Размер: 4.84 mb Название файла: Язык инструкции:

If you do not do this, the extended pump and(or) solenoid valve could become plugged up with debris. Remove the brushes or pad holders. Rinse the brushes or pads with warm water and hang up to dry. Allow buffing pads to dry completely before using again. NOTE: You can either remove the brushes manually or automatically by pressing and holding the Scrub OFF Switch (H) for 5 seconds (EDS disk models only). Remove the squeegee, rinse it with warm water and hang it up to dry. Check the maintenance schedule below and perform any required maintenance before storage. MAINTENANCE SCHEDULE MAINTENANCE ITEM Daily Weekly Monthly Yearly Charge Batteries X Check/Clean/Rotate the Brushes/Pads X Check/Clean the Squeegee X Clean Hopper on Cylindrical System X Purge the Extended Scrub System(if installed) X Check Each Battery Cell(s) Water Level (does not apply to gel cell batteries) X Inspect Scrub Housing Skirts X Inspect and clean Solution Filter X Clean Solution Manifolds on Cylindrical System X Purge Detergent System (EDS only) X Lubricate the Machine * Check Carbon Brushes X * Have Nilfisk check the vacuum motor carbon motor brushes once a year or after 300 operating hours. The brush and drive motor carbon brushes check every 500 hours or once a year. NOTE: Refer to the Service Manual for more detail on maintenance and service repairs. 8 Store the machine in a clean, dry place. 9 Turn the Master Key Switch (A) OFF (O) and remove the key. SERVICING THE VACUUM MOTOR Have your Nilfisk Dealer check the carbon motor brushes once a year or after 300 operating hours. Motor damage resulting from failure to service the carbon brushes is not covered under warranty. See the Limited Warranty Statement. LUBRICATING THE MACHINE Once a month, apply light machine oil to lubricate the: • General Pivot Points For the Squeegee Linkage (A). • Squeegee mount angle adjustment knob threads (B). • Squeegee Tool end wheels (C). • General Pivot Points For the Brush Linkage (D). • Scrub deck bumper wheels. Once per quarter, Grease the following • Rear Caster Wheel Swivels (E). 4 5 X X FORM NO. - 56041684 - BA 755, BA 855 - B-17 B-18 / ENGLISH CHARGING WET BATTERIES EDS - Charge the batteries each time the machine is used or when the Battery Indicator (D5) is reading less than full. Standard - Charge the batteries each time the machine is used or when the Battery Indicator (J1) is flashing RED. A WARNING! Do not fill the batteries before charging. Charge batteries in a well-ventilated area. Do not smoke while servicing the batteries. When Servicing Batteries... * Remove all jewelry * Do not smoke * Wear safety glasses, rubber gloves and a rubber apron * Work in a well-ventilated area * Do not allow tools to touch more than one battery terminal at a time * ALWAYS disconnect the negative (ground) cable first when replacing batteries to prevent sparks. * ALWAYS connect the negative cable last when installing batteries. If your machine shipped with an onboard battery charger do the following: Turn the Key Switch (A) OFF. Unwind the electrical cord from the side of the onboard charger and plug it into a properly grounded outlet. Refer to the OEM product manual for more detailed operating instructions. If your machine shipped without an onboard battery charger do the following: Disconnect the batteries from the machine and push the connector from the charger into the Battery Pack Connector (18). Follow the instructions on the battery charger. SERVICE NOTE: Make sure you plug the battery charger into the connector with the handle attached to it. M CAUTION! To avoid damage to floor surfaces, wipe water and acid from the top of the batteries after charging. CHECKING THE BATTERY WATER LEVEL Check the water level of the batteries at least once a week. After charging the batteries, remove the vent caps and check the water level in each battery cell. Use distilled or demineralized water in a battery filling dispenser (available at most auto parts stores) to fill each cell to the level indicator (or to 10 mm over the top of the separators). DO NOT over-fill the batteries! Acid can spill onto the floor if the batteries are overfilled. Tighten the vent caps. Wash the tops of the batteries with a solution of baking soda and water (2 tablespoons of baking soda to 1 liter of water). CHARGING GEL (VRLA) BATTERIES EDS - Charge the batteries each time the machine is used or when the Battery Indicator (D5) is reading less than full. Standard - Charge the batteries each time the machine is used or when the Battery Indicator (J1) is flashing RED. M WARNING! Charge batteries in a well-ventilated area. Do not smoke while servicing the batteries. When Servicing Batteries... * Remove all jewelry * Do not smoke * Wear safety glasses, rubber gloves and a rubber apron * Work in a well-ventilated area * Do not allow tools to touch more than one battery terminal at a time * ALWAYS disconnect t...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: