Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Locate and organize all parts before assembly. Familiarize yourself with the parts and where they go. Following this User’s Guide will greatly enhance your ability to get the most performance from your BISSELL QuickSteamer for many years. Your QuickSteamer comes in three, easy to assemble components: Handle assembly Upper Handle assembly Clean/Solution Tank 3 Screws The only thing you will need to assemble your cleaner is a Phillips head screwdriver. Assembling Your QuickSteamer 1. Slide Upper Body into Lower Body. 2. Secure with Screws. 3. Slide Strain Reliever Handle down into Upper Body until it will go no further. 4. Secure with Screw. 5. Place Clean/Solution Tank on back of unit. Special Features Clean/Solution Tank - holds 1/2-gallon of hot water and cleaning solution. Collection Tank - holds 1/2-gallon of dirty water. Power Cord - for storage, wrap Power Cord around Upper and Lower Cord Wraps, and secure plug to Cord with molded clip. 4 1 2 5 3 800.237.7691 5 ug603-5603_1770_206.indd 5 2/28/06 4:27:17 PM How to Use Your BISSELL QuickSteamer Before You Clean 1. Plan activities to give carpet time to dry. 2. Remove easily moved furniture (chairs, lamps, coffee/cocktail tables, etc.) from room if needed. 3. Vacuum carpet thoroughly. 4. Decide where to begin — and end — your job. Clean in 3’ X 4’ sections, starting in areas farthest from exit. Plan to leave a path open to empty soiled water and refill cleaner. 5. Carpeting will dry in three to four hours, depending on carpet style and air circulation in room. A floor fan speeds drying. 6. Replace furniture on damp carpeting by placing waxed paper under legs until floor dries completely. Fill the Tank 1. Remove the Clean/Solution Tank by lifting it straight up, then away from the Lower Body. WARNING: To reduce the risk of fire, use only BISSELL Cleaning Formulas for Deep Cleaning Machines. Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void warranty. Chemical spot cleaners or solvent-based soil removers should not be used. These products may react with the plastic materials used in your QuickSteamer, causing cracking or pitting. 2. Unscrew the black cap at the bottom of the Clean/Solution Tank. Tip: 3. Add one of the BISSELL Advanced Cleaning formulas for Deep Cleaning machines to the formula fill Always vacuum thoroughly before line on the Clean/Solution tank. Fill the rest of the you deep clean. If possible, move tank with hot (not boiling) tap water to the water large furniture to an area you will fill line. Replace and tighten the black cap. not be cleaning. 4. Place Clean/Solution Tank on Lower Body. 5. Rotate Quick Release Cord Wrap™ to release the Power Cord and plug into an outlet. Pre-Treating Pre-treat stubborn stains and highly soiled carpet in hallways and other high-traffic areas. 1. Using BISSELL Tough Stain pre-cleaner, generously spray evenly over soiled area, do not overwet carpet. 2. Wait 3 -5 minutes before deep cleaning. Tip: Deep cleaning spots, spills and high traffic areas on a regular basis can prolong carpet life. 2. 6 800.237.7691 ug603-5603_1770_206.indd 6 2/28/06 4:27:21 PM 1. With your foot, press the red Power Switch [located in foot of unit] ON. 2. With foot, press the Detent Lever on right side of Lower Body. 3. Depress Spray Trigger to spray cleaning solution. Do not overwet. 4. Carpet Cleaning1. With your foot, press the red Power Switch [located in foot of unit] ON. 2. With foot, press the Detent Lever on right side of Lower Body. 3. Depress Spray Trigger to spray cleaning solution. Do not overwet. 4. Carpet CleaningTo suction up water, repeat motion over same area without depressing Trigger. 5. Repeat Steps 3 and 4 until no more dirt can be removed. 6. Continue to clean entire carpet, working in 3’ x 4’ sections. 7. Empty the Collection Tank when dirty water reaches the full line, or when the Clean/Solution Tank is empty. See page 8 for instructions. 8. If Floor Nozzle stops spraying, turn Power Switch OFF and check water and cleaning solution levels. Refill if needed. Hard Floor Cleaning 1. Attach Hard Floor Tool to Unit. 2. Remove the Collection Tank (refer to #3a and b in the Routine Maintenance section on page 8) A. For 1770/1970 series it is necessary to remove the Cross Action Brush first. Using your thumbs squeeze the 2 grey tabs towards the outside of the unit. Push down at the same time and release the Cross Action Brush. 3. Attach the Hard Floor Tool by hooking it into the front of the removable nozzle and swinging it down until the tabs pop into place. 4. Replace the Collection Tank. Be sure to attach the 2 latches. 5. Fill Clean/Solution Tank with BISSELL Hard Floor Solutions™ to FORMULA fill line. 6. Fill Clean/Solution Tank with hot (not boiling) tap water to the WATER fill line. 7. Follow steps 1-8 in Deep Cleaning section above. Tip: It is recommended that every time your Clean/Solution Tank is emptied of solution that you empty the c...
Эта инструкция также подходит к моделям:Пылесосы - 1770 (514.52 kb)