Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
13. Wrap flex hose around tool rack. 14. Empty collection tank and rinse out, following instructions on page 10. 15. If the ReadyTools dial becomes difficult to turn, the diverter assembly that holds the dial may need to be cleaned. To clean, flush hot water through the nozzle. Make sure the dial is set to FLOOR CLEANING. 9 800.237.7691 ug120-4080_7350_908.indd 9 10/14/08 1:25:59 PM Operation Rubber Stopper Oxy Gen2 PowerTool™ To use the Oxy Gen2 PowerTool: 1. Pull out the rubber stopper in the tank. 2. Fill with Oxy Gen2® formula. 3. Replace the rubber stopper and attach the tool to the hose grip. 4. Refer to page 9 “Ready Tools” steps 9-15. Maintenance and care Machine care For best results, a few simple steps can assure your machine is well maintained after your Lint Screen cleaning is complete. 1. Turn power switch OFF ( 0 ). Unplug the machine and wrap the power cord. 2. After emptying the collection tank, rinse it with running hot tap water, taking care to clean all around the interior. 3. Clean out the lint screen if necessary by wiping clean any visible residue. 4. Replace the collection water tank on the machine. 4. Any loose hair or debris can be pulled from the TLR PowerRoller and thrown away. 5. To clean the attachments, remove from hose and rinse in clean, running water. Dry before storing. Clean the hose by suctioning clean water from the tap. Before wrapping back on machine, lift end of hose and stretch out to ensure all water is cleared from hose while still suctioning. 6. Wipe the machine’s exterior with a soft cloth and store properly, refer to page 11. 10 800.237.7691 ug120-4080_7350_908.indd 10 10/14/08 1:26:00 PM 800.237.7691800.237.7691 9. 800.237.7691800.237.7691 9. 1. the machine. 2. Maintenance and careCleaning/replacing the TLR Power Roller Turn power switch to OFF ( O ) and unplug 3. Remove both tanks, detent the handle and turn the machine on its back. 3. Remove the 6 screws from the sole plate using a Phillips head screwdriver, set 6 screws and sole plate aside. 4. Turn the machine on its side so the cord side is against the floor. 5. Remove the 2 screws from the belt guard and set aside Note: These 2 screws are the same as the 6 sole plate screws). Remove the top of the belt guard. 6. Unhook the belt from the TLR PowerRoller and slide the roller down through the hole in the belt guard bottom. Slide the roller up off the metal dowel (which is attached to the swing arm). 7. Clean the TLR PowerRoller by rinsing with hot water and mild soap. Allow to dry before replacing if desired. 8. To replace, slide the TLR PowerRoller on to the metal dowel with the taller cog at the top. Push the taller cog of the roller back up through the hole in the belt guard bottom and re-attach the belt. Place the belt guard top into position over the bottom half and tighten together with 2 screws. 9. Turn the machine on to its back and attach the second swing arm. Be sure the arm is properly in place both on the TLR PowerRoller and in the base. Push the TLR PowerRoller down so it is nested under the nozzle. 10. Re-attach the sole plate using the 6 screws. Machine storage Put the unit away in a closet or basement for the next use. Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty. www www.bissell.com.bissell.com 5. 6.6a. 8a. 8b. 8c. 11 ug120-4080_7350_908.indd 11 10/14/08 1:26:02 PM Troubleshooting Reduced Spray OR No Spray Possible cause Remedies 1. Clean/solution tank may be empty WARNING: To reduce the risk of fire, electric shock or injury, unplug from theoutlet before servicing. 1. Turn power switch OFF; Refill tank with clean hot tap water and formula 2. Clean/solution tank may not be seated properly 2. Turn power switch OFF; remove tank and reseat 3. Pump may have lost prime 3. Turn power switch OFF ( O ); after 1 minute turn ON ( I ) and depress spray trigger Be sure there is cleaning formula in the clean/solution tank, it will make the machine prime faster No spray through the hose Possible cause Remedies 1. Pump may not be primed 1. Turn ReadyTools dial to FLOOR CLEANING and depress trigger for a few a seconds until you see suction coming up the nozzle Turn ReadyTools dial back to TOOLS TLR PowerRoller Does Not Turn Possible cause Remedies 1. The brush belt is off or broken 1. Refer to page 11, steps 1-5 for instructions on how to access the belt 2. Look at the belt and check for breakage or mis-alignment on the cogs. IF there is no evidence, replace all parts following steps 8-11. 3. In the event your belt is broken, a replacement belt may be ordered at or by calling BISSELL consumer services at 800-237-7691. Refer to the parts list on page 14. Complete installation instructions will come with the replacement belt Machine not picking up solution Possible cause Remedies 1. Collection tank ma...
Эта инструкция также подходит к моделям:Пылесосы - PRODRY 8350 (669.86 kb)